Alpine dha-s680 Guía Del Usuario
FR
ES
DE
SE
IT
45
-EN
6
5
3
4
2
1
6
5
3
4
2
1
L-shaped
bracket holes
bracket holes
H
V
0
°
0
°
90
°
H
V
90
°
Vertical
Horizontal
Use one of each
of holes and
of holes and
,
and fasten the
two screws
diagonally.
two screws
diagonally.
Use one of each
of holes and ,
and fasten the
two screws
diagonally.
of holes and ,
and fasten the
two screws
diagonally.
6
6
1
3
Diagonal
To be fastened
using the holes
and .
using the holes
and .
3
4
Change the position of the springs.
With this product, the positions of the built-in
anti-vibration springs must be changed
according to the angle of installation. The product
will not provide the regular resistance to vibration
if the anti-vibration springs are not in the correct
positions or if the left and right springs are in
different positions.
The anti-vibration springs can be placed at one
of five angles.
The springs are set to the “H” angle upon
shipment from the factory. To change this angle,
follow the instructions given below.
1
anti-vibration springs must be changed
according to the angle of installation. The product
will not provide the regular resistance to vibration
if the anti-vibration springs are not in the correct
positions or if the left and right springs are in
different positions.
The anti-vibration springs can be placed at one
of five angles.
The springs are set to the “H” angle upon
shipment from the factory. To change this angle,
follow the instructions given below.
1
Change the position of
the springs using a
finger.
the springs using a
finger.
2
Stick on the left and right
side surface cover labels.
Be sure to apply the
cover labels after setting
the position of the
springs so as to protect
the interior of the product from dust or dirt
which may cause malfunction.
side surface cover labels.
Be sure to apply the
cover labels after setting
the position of the
springs so as to protect
the interior of the product from dust or dirt
which may cause malfunction.
3
Check the position of the springs. Make a
final check of the position of the springs
using the five small holes in the left and right
side surface cover labels.
final check of the position of the springs
using the five small holes in the left and right
side surface cover labels.
• Floor base installation
1
Determine the position under the carpet at
which the unit is to be installed.
which the unit is to be installed.
2
Insert the hexagonal bolts (M6x25)
5
into
the floor base
3
, then mount directly on the
floor using the hexagonal washer faced self-
tapping screws (M5x15)
tapping screws (M5x15)
1
.
Remove the shipping keys.
Three keys are mounted to the DHA-S680’s
bottom panel to protect the product during
transportation. Be sure to remove these keys
before installing the DHA-S680. So as not to
lose the keys, store them in the special plastic
pouch provided with the DHA-S680 and cover
the key holes with the included dust-prevention
seals.
bottom panel to protect the product during
transportation. Be sure to remove these keys
before installing the DHA-S680. So as not to
lose the keys, store them in the special plastic
pouch provided with the DHA-S680 and cover
the key holes with the included dust-prevention
seals.
NOTE
The eject operation cannot be performed if the keys are
mounted when the power is turned on. Turn the power
off, then remove the keys.
mounted when the power is turned on. Turn the power
off, then remove the keys.
2
Install the L-shaped bracket.
1
Determine the position and angle of
installation.
installation.
2
Referring to step 3, change the position of
the springs according to the angle of
installation.
the springs according to the angle of
installation.
3
Install the L-shaped bracket
2
according to
the angle of installation. Fasten it in place
using the double washer screws (M4x8)
using the double washer screws (M4x8)
6
.
■
Example of Installation Using Attached L-
shaped bracket.
shaped bracket.
1
1
3
5
5
1
3