Alpine IVA-D300 Guía Del Usuario
55
-EN
MobileHub™ Link
(Optional)
(Optional)
About MobileHub™ Link (Optional)
Connect a separately sold junction box and a portable telephone
(available from Nokia) to control the incoming and outgoing calls of
the portable telephone.
(available from Nokia) to control the incoming and outgoing calls of
the portable telephone.
CAUTION
• Even with hands-free operation, a driver can be distracted
during telephone operation or receiving a call. For the
sake of safety, drivers are requested to refrain from
operating the telephone while driving.
sake of safety, drivers are requested to refrain from
operating the telephone while driving.
• For the sake of safety, operations other than incoming
calls and Speed-Dial outgoing calls cannot be used.
• If a portable telephone is connected, its address book, incoming
and outgoing history, short message history and standardized
sentences are downloaded to the junction box.
Please refer to the instruction manual of the junction box.
sentences are downloaded to the junction box.
Please refer to the instruction manual of the junction box.
• When a portable telephone is not connected, “NO PHONE” is
displayed for at least 5 seconds, then the mode returns to the
original source mode.
original source mode.
• When the portable telephone is taken off the junction box during an
incoming or outgoing call, or during a hands-free call, the call will
be treated as an ordinary one by the portable telephone.
be treated as an ordinary one by the portable telephone.
• When there is an incoming call while the power of the IVA-D300 is
OFF, the power of the IVA-D300 turns ON automatically, hands-
free call is cut, and the portable telephone call is enabled.
free call is cut, and the portable telephone call is enabled.
• Even if the power of the portable telephone is OFF, when IVA-
D300 is set to the telephone mode, the power of the portable
telephone will be turned ON.
telephone will be turned ON.
• If the ACC power of the vehicle is turned OFF (the engine is
stopped) during a hands-free call, the hands-free call cuts, and the
portable telephone call is enabled.
portable telephone call is enabled.
• If there is an incoming call during operation (except an outgoing
call or talking), operation mode will end and switch to the
incoming or talking mode.
incoming or talking mode.
• An outgoing call from a portable telephone is also possible.
However, you cannot perform different operations at the same time
from a portable telephone and IVA-D300 as malfunction can result.
from a portable telephone and IVA-D300 as malfunction can result.
• With a junction box connected outgoing, incoming, and sending
history will also be recorded in the portable telephone.
• While telephoning, Time Correction is set to normal (0.0ms) and
DEFEAT is also set to ON. When the call has finished, the unit
returns to the setting which you previously set.
returns to the setting which you previously set.
• The telephone volume can be adjusted from the IVA-D300. The
volume you set during the call is memorized, and is automatically
applied again on the next call.
applied again on the next call.
Displaying the Category/Channel Name Title
List
List
1
In XM mode, touch [
].
The category title list is displayed.
Screen example for category search list
1 Turns the page
2 Touch [:] to receive the selected category channel
2 Touch [:] to receive the selected category channel
directly.
3 [
] is displayed if there is a hierarchical list.
Touch [
] to change the channel name search
screen of the selected category.
4 Category UP/DOWN can directly be performed.
Screen example for channel name search list
1 Turns the page
2 Returns to the category search list.
3 The selected channel is received.
4 Category UP/DOWN can directly be performed.
2 Returns to the category search list.
3 The selected channel is received.
4 Category UP/DOWN can directly be performed.
2
Touch [:] of the selected Category or Channel
name.
name.
The channel in the selected category is tuned.
Selecting the Channel directly
You can directly select the channel number on the display of the
numeric keypad.
numeric keypad.
1
Touch [P1/3] twice in the XM mode.
The function guide appears.
2
Touch [10KEY].
The numeric keypad input screen is displayed.
3
Touch to input the channel number.
4
Touch [ENT].
The selected channel is received.
4
1
2
3
1
2
3
4