Delfield mdbr1-gh Instruccion De Instalación
Meridian Series
®
Reach-Ins Service and Installation Manual
For customer service, call (800) 733-8829 or (800) 733-8948, Fax (989) 773-3210, www.delfield.com
14
Meridian Series
®
Reach-Ins Service and Installation Manual
15
For customer service, call (800) 733-8829 or (800) 733-8948, Fax (989) 773-3210, www.delfield.com
The ERC-2 Electronic Refrigeration Control is a microprocessor-based
electronic controller designed to control both the temperature and the
defrost functions of a commercial refrigeration unit. Designed for 115
or 208/240 (50 or 60 Hz), the control comes with four relay outputs:
compressor, defrost, evaporator fan and alarm.
The ERC-2 includes a digital display module that provides readout of
the temperature, time and built-in diagnostics. The display module
can be mounted locally or remotely from the unit and it contains a
touch keypad for simple programming. For defrost control, it uses a
real time clock.
Applications:
This control is NSF certified and it can be applied to many different
commercial refrigeration applications like reach-ins, walk-ins, refriger-
ated cases, or other different products where accurate control of
refrigerated space and defrost cycles is required.
Technical Specifications
Input Power: 115/208-240 VAC 50/60Hz (-10%, -15%)
Zone and Evaporator Temperature Sensor: NTC thermistor: Range
-40 to 199°
Output Relay Ratings:
Compressor: 1hp@115V
Defrost: 16A resistive at 115/208-240V pilot duty 470 VA@120/
208-240V
Evaporator fan: 1/2 hp at 120V, 3/4 hp at 208V, 1 hp at 240V
Alarm: 5A resistive at 115/208V
Ambient Operating Conditions: -40% to 122°F; 0 to 95% RH
Agency Certifications UL, CSA, NSF
Special Features
The default parameters for Delfield will be pre-programmed.
In case of a power failure, the control has a safe operating mode in
case of sensor failure.
Programming
Accessing
Level 1: Press and hold the SET button for five sec.
Level 2: Press and hold the SET and DOWN button for 10 sec.
Programming
Scroll through the parameters using the UP and DOWN arrow keys.
Choose the parameter to be changed by pressing SET. Scrolling
through the options or set the time or temperature by using the UP
and DOWN arrow keys. Once you choose the option or adjusted the
time or temperature, press SET to accept the option.
The ERC-2 control initially powers up displaying 12 AM otherwise
it will show the last configured selection (time or temperature). If
a power outage occurs during normal operation, the control will
maintain the correct time of day using a capacitor (batteries are not
required). The time will be maintained for up to 100 hours when the
capacitor is fully charged.
To initiate a Manual Defrost, press and hold the MAN DEF key for 3
seconds.
There are two levels of programming in the ERC-2. The first of secu-
rity will enable the user to set two parameters: Time-of-day (CLoC
and setpoint temperature SET). The other level allows access to the
other parameters.
Three buttons are used for the programming: SET, UP AND DOWN.
STEP 1 SET
Press and hold SET for 5 seconds. The
display will show CLoC
STEP 2 SET
Press SET again to change the time of
day.
STEP 3 UP OR DOWN Press UP or DOWN until the correct time
of day is displayed.
STEP 4 SET
Press SET to accept the new time.
STEP 5 DOWN
Press DOWN to go to the next parameter
- Set point temperature -SEt (cut out).
STEP 6 SET
Press SET to change the set point tem-
perature.
STEP 7 UP OR DOWN Press UP or DOWN to go to the desired
setpoint. The range is - 40° to 60°F or
-40 to 16°C.
STEP 8 SET
Press SET to accept the change.
STEP 9 DOWN
Press DOWN to exit the first level of
programming.
NOTE 1: During programming, if no button is pushed
during 30 seconds, the control will go back to the
normal operating mode. This is valid for both pro-
gramming levels.
NOTE 2: When changing the time, press and hold the
MAN DEF button for 3 seconds to change the AM/PM
mode.
NOTE: By lifting gray plastic cover, buttons will be exposed.
For more information on the ERC Control, please log onto our web
site at www.delfield.com and go to the Parts and Service section, then
to the Service Department page.
ERC CONTROL (OPTIONAL)