Citel 1000 Manual Suplementario
070707
Page 2 of 3
Copyright 2007 Citel plc All Rights Reserved
ERROR
CODES
CODES
DESCRIPTION
EXPLANATION
109A
Number of times Extender or phone signaling
channel timed out waiting for packet
acknowledgment.
channel timed out waiting for packet
acknowledgment.
Did not get a V42 signaling acknowledgement.
As long as you are not getting 106B errors, this
is not necessarily a problem. Excessive errors
or 106B errors indicate a problem with the
Analog line.
As long as you are not getting 106B errors, this
is not necessarily a problem. Excessive errors
or 106B errors indicate a problem with the
Analog line.
110C
Number of times Extender or phone signaling
channel transmit locked up (transmit buffers full
when no data to send).
channel transmit locked up (transmit buffers full
when no data to send).
The 8 second TX timer timed out and buffers
were full. This should not occur. Needs further
investigation by customer service. Possibly a
hardware/software error.
were full. This should not occur. Needs further
investigation by customer service. Possibly a
hardware/software error.
111A
Number of rejected serial data packets
received because they were out of sequence.
received because they were out of sequence.
Far end rejected the signaling packet. Might
occur often. Should not cause a significant
functional problem.
occur often. Should not cause a significant
functional problem.
112B
Number of times serial data packet re-
transmissions exceeded maximum (Causes
serial data to be lost).
transmissions exceeded maximum (Causes
serial data to be lost).
Same as ‘111A’.
113B
Number of times serial data channel had to be
re-synchronized.
re-synchronized.
Same as ‘107B’.
114A
Number of times serial data channel timed out
waiting for packet acknowledgment.
waiting for packet acknowledgment.
Same as ‘109A’
115B
(not incremented, analog uses 136/137) UD
channel discarded data due to Rx overflow (no
HW flow control)
channel discarded data due to Rx overflow (no
HW flow control)
N/A
116B
TA/Modem - Loss of carrier
Possibly a bad analog line. The connection to
the other end was broken. The other end could
have powered cycled or the wiring to the analog
lines could be faulty.
the other end was broken. The other end could
have powered cycled or the wiring to the analog
lines could be faulty.
117C
(not incremented on analog) TA check failed
N/A
118C
(not incremented on analog) communications
to DSP failed
to DSP failed
N/A
119B
Number of times Digital port link re-activated.
Office side only.
Office side only.
Digital port connection to the Office Module may
have intermittent connection problems. Digital
port signaling was temporarily lost and re-
initialized. Check the Digital port wiring.
have intermittent connection problems. Digital
port signaling was temporarily lost and re-
initialized. Check the Digital port wiring.
120B
Number of times Digital port connection was
lost or de-activated. Every 120B error also
increments 119B.
lost or de-activated. Every 120B error also
increments 119B.
Digital port connection to the Office Module may
have been lost. Check the Digital port wiring.
have been lost. Check the Digital port wiring.
121A
(not incremented on analog)
N/A
122B
RVP (V42 link) failed, only incremented on
Office side
Office side
Digital port connection to the Office Module may
have been lost. Check Digital port wiring. Very
poor analog line connection. No valid packet
transmission between the Office and Remote
modules.
have been lost. Check Digital port wiring. Very
poor analog line connection. No valid packet
transmission between the Office and Remote
modules.
123A
User has accessed the Disconnect menu
Indicates that the user has disconnected by
pressing Hold button 4 times and selecting
Disconnect.
pressing Hold button 4 times and selecting
Disconnect.