ONKYO TX-NR901 Manual De Instrucciónes
88
Using the Remote Controller with Other
Components
You can use the TX-NR901’s remote controller (RC-
548M/RC-549M) to control your other AV components,
including those made by other manufacturers. To do this
you can:
548M/RC-549M) to control your other AV components,
including those made by other manufacturers. To do this
you can:
• Enter a remote control code for the component that
you want to control (e.g., DVD, TV, VCR).
• Learn commands directly from the other component’s
remote controller (see page 93).
• Use the Macro function to learn a sequence of actions
(see page 94).
• You can also edit the remote controller modes (see
page 96).
By entering the appropriate remote control code for each
of your components, you can control each component by
selecting the relevant remote controller mode: DVD, TV,
VCR, CBL (cable), or SAT (satellite).
of your components, you can control each component by
selecting the relevant remote controller mode: DVD, TV,
VCR, CBL (cable), or SAT (satellite).
Remote Control Codes for an Onkyo DVD
Player
The remote control code that you use with an Onkyo
DVD player depends on whether it’s connected via
DVD player depends on whether it’s connected via
,
as follows:
5001:
Use this code if you’ve connected an
cable
and an RCA/phono analog audio cable to your
DVD player. This is the default setting, so if
you’re using
DVD player. This is the default setting, so if
you’re using
, you don’t need to change it.
Point the remote controller at the TX-NR901 to
operate the DVD player.
operate the DVD player.
5002:
Use this code if your DVD player doesn’t have
an
an
socket, or you’re not using
. Point
the remote controller at the DVD player to
operate it.
operate it.
Entering a Remote Control Code
1
Look up the appropriate remote
control code for the component.
control code for the component.
See “Remote Control Codes” on
page 89
page 89
2
Press and hold down the [CUS-
TOM] button for more than three
seconds.
TOM] button for more than three
seconds.
The remote controller enters Custom
mode.
mode.
3
Roll the scroll wheel to select
“PRGRM,” and then press the
scroll wheel.
“PRGRM,” and then press the
scroll wheel.
4
Roll the scroll wheel to select the
the remote controller mode you
want to use with the component,
and then press the scroll wheel.
the remote controller mode you
want to use with the component,
and then press the scroll wheel.
The following remote controller modes
can be selected: DVD, TV, VCR, CBL,
or SAT.
can be selected: DVD, TV, VCR, CBL,
or SAT.
CUSTOM
5
Use the number buttons to enter
the 4-digit remote control code.
the 4-digit remote control code.
If the code is accepted,
the following
appears on the display for awhile, and
then the normal display reappears.
then the normal display reappears.
If the code is not accepted,
after the
message “RETRY” has been displayed,
the code entry display reappears, and
you should try entering the code again.
the code entry display reappears, and
you should try entering the code again.
To cancel this procedure at any point,
press the [CUSTOM] button.
press the [CUSTOM] button.
6
Select the remote controller
mode, point the remote control-
ler at the component, and check
its operation.
mode, point the remote control-
ler at the component, and check
its operation.
The remote controller buttons that can
be used in DVD mode are shown on
page 16. Those that can be used with
the TV, VCR, CBL, and SAT modes are
listed on pages 91 and 92.
be used in DVD mode are shown on
page 16. Those that can be used with
the TV, VCR, CBL, and SAT modes are
listed on pages 91 and 92.
@. - ' /
ABC
DEF
PQRS
TUV
WXYZ
GHI
JKL
MNO
0
1
2
3
4
5
6
7
8
9
TX-NR901_En.book Page 88 Wednesday, October 1, 2003 9:44 AM