Samsung clp-775 Manual De Usuario

Network setup_ 34

15. If the test page prints out correctly, click Yes.

If not, click No to reprint it.

16. To register as a user of the machine in order to receive information 

from Samsung, click On-line Registration.

17. Click Finish.

If you do not have an access point (AP), you may still connect the 

machine wirelessly to your computer by setting up an ad-hoc wireless 

network by following the simple steps below.

•

Network-connected computer

•

Software CD that was provided with your machine

•

The machine installed with a wireless network interface

•

USB cable

1. Check whether the USB cable is connected to the machine.
2. Turn on your computer and the wireless network machine.
3. Insert the supplied software CD into your CD-ROM drive.
4. Select the Wireless Setting and Installation option.

•

Install Now:  If you have already set up the wireless network, 

click this button to install the machine’s driver to use the wireless 

network machine. If you have not set up the wireless network, 

click the Wireless Setting and Installation button to set up the 

wireless network before you click this button. 

•

Wireless Setting and Installation:  Configure the wireless 

network settings of your machine with a USB cable then install 

the machine driver. This is only for users who have not set up the 

wireless connection before.

5. Read the License Agreement, and select I accept the terms of the 

License Agreement. Then, click Next.

6. The software searches the wireless network.

If the software has failed to search the network, check if the 

USB cable is connected properly between the computer and 

machine, and follow the instruction in the window.

7. After searching the wireless networks, a list of wireless networks 

your machine has searched appears. 
If you want to use the Samsung default ad hoc setting, select the last 

wireless network on the list, Network Name(SSID) is portthru and 

Signal is Printer Self Network.
Then, click Next.
If you want to use other ad hoc settings, select another wireless 

network from the list. 

If you want to change ad hoc settings click the Advanced 

Setting button. 

•

Enter the wireless Network Name:  Enter the SSID name 

you want (SSID is case-sensitive).

•

Operation Mode:  Select ad hoc.

•

Channel:  Select the channel. (Auto Setting or 2412 MHz 

to 2467 MHz).

•

Authentication:  Select an authentication type.
Open System:  Authentication is not used, and encryption 

may or may not be used, depending on the need for data 

security.
Shared Key:  Authentication is used. A device that has a 

proper WEP key can access the network.

•

Encryption:  Select the encryption (None, WEP64, 

WEP128).

•

Network Key:  Enter the encryption network key value.

•

Confirm Network Key:  Confirm the encryption network 

key value.

•

WEP Key Index:  If you are using WEP Encryption, select 

the appropriate WEP Key Index.

The wireless network security window appears when the ad 

hoc network has security setting.
The wireless network security window appears. Select Open 

System or Shared Key for the authentication and click Next.

•

WEP (Wired Equivalent Privacy) is a security protocol 

preventing unauthorized access to your wireless network. 

WEP encrypts the data portion of each packet exchanged 

on a wireless network using a 64-bit or 128-bit WEP 

encryption key.

8. The window showing the wireless network setting appears. Check 

the settings and click Next.

Before entering the IP address for the machine, you must know 

the computer’s network configuration information. If the 

computer’s network configuration is set to DHCP, the wireless 

network setting should also be DHCP. Likewise, if the 

computer’s network configuration is set to Static, the wireless 

network setting should also be Static.
If your computer is set to DHCP and you want to use the Static 

wireless network setting, you must contact the network 

administrator to get the static IP address.

•

For the DHCP method
If the IP address assignment method is DHCP, check if 

DHCP is shown in the Wireless Network Setting Confirm 

window. If it shows Static, click Change TCP/IP to change 

the assignment method to Receive IP address 

automatically (DHCP).

•

For the Static method
If the IP address assignment method is Static, check if 

Static is shown in the Wireless Network Setting Confirm 

window. If it shows DHCP, click Change TCP/IP to enter 

the IP address and other network configuration values for 

the machine.
For example:
If the computer’s network information is as shown follows:

-

IP address: 169.254.133.42

-

Subnet Mask: 255.255.0.0

Then, the machine’s network information should be as