Furuno gp-150-dual Guía Del Usuario
4. NAVIGATION PLANNING
4-5
Erasing waypoints through the
waypoint list
1) Press
WPT RTE and 4.
2) Press or to select waypoint to
erase.
3) Press the
CLEAR key. The message
shown in Figure 4-13 appears if the
waypoint is currently selected as
destination, is part of a route, or is in the
route currently selected as destination.
waypoint is currently selected as
destination, is part of a route, or is in the
route currently selected as destination.
This wpt is GOTO
This wpt is in registered route
This wpt is in selected route
This wpt is in registered route
This wpt is in selected route
1st line
Are you sure to erase ?
ENT: Yes
MENU: No
Figure 4-13
Note: All waypoint marks (as well as all
other marks) and their data can be
erased collectively by clearing the
Plotter memory. For further details,
see page 9-1.
erased collectively by clearing the
Plotter memory. For further details,
see page 9-1.
4) Press the
NU/CU ENT key.
Note: To cancel erasure, press the
MENU ESC key instead of the
NU/CU ENT key. The waypoint list
appears.
5) Press the
MENU ESC key.
4.4 Entering
Routes
Often a trip from one place to another
involves several course changes, requiring a
series of route points which you navigate to,
one after another. The sequence of
waypoints leading to the ultimate destination
is called a route. The GP-150-DUAL can
automatically advance to the next waypoint
on a route, so you do not have to change the
destination waypoint repeatedly.
The GP-150-DUAL can store 30 routes and
each route may contain up to 30 waypoints.
Routes can be registered while in the Plotter
1 or Plotter 2 display mode. Routes are
mutually registered when the navigators are
sharing data.
involves several course changes, requiring a
series of route points which you navigate to,
one after another. The sequence of
waypoints leading to the ultimate destination
is called a route. The GP-150-DUAL can
automatically advance to the next waypoint
on a route, so you do not have to change the
destination waypoint repeatedly.
The GP-150-DUAL can store 30 routes and
each route may contain up to 30 waypoints.
Routes can be registered while in the Plotter
1 or Plotter 2 display mode. Routes are
mutually registered when the navigators are
sharing data.
Entering routes
1) Press the
WPT/RTE key.
2) Press
5 to select Route Planning. The
route list appears.
ROUTE LIST
ENT: Enter
MENU: Escape
No. PTS Total Dist. TTG Remarks
01
12D15H28M
1234 . 56 nm
D H M
. nm
30
UseFwd
02
2D08H35M
234 . 56 nm
25
03
*9D*9H*9M
*999. 99 nm
30
04
D H M
. nm
05
34D23H45M
6543 . 21 nm
30
06
: Edit
: Route No.
Remarks
Use: In use
Fwd: Traverse waypoints in forward order
Rvs: Traverse waypoints in reverse order
Use: In use
Fwd: Traverse waypoints in forward order
Rvs: Traverse waypoints in reverse order
Figure 4-14 Route list
3) Press or to select an empty route
number.
4) Press .
The route planning/waypoint list window
appear as shown in Figure 4-15. The
waypoint list window lists the position and
data for each registered waypoint. No
position or data appears for empty waypoints.
appear as shown in Figure 4-15. The
waypoint list window lists the position and
data for each registered waypoint. No
position or data appears for empty waypoints.