Craftsman 38907 Manual De Usuario
11
Emptying the Collection Tank
Clean the Blower Intake
Maintenance
1. Verify that the power cord is
disconnected from the outlet. (Fig. 1)
2. Disconnect the hose from the vacuum.
(Fig. 2)
3. Undo the latches and remove the power
head from the collection tank. (Fig. 3)
Place power head on a soft, clean
surface upside down.
4. Clear all dirt or debris from the collection
tank and hose into a proper waste
container. (Fig. 4)
5. Clean or replace the fi lters.
6. Check the hose, attachments, and
power cord to verify that they have not
been damaged.
disconnected from the outlet. (Fig. 1)
2. Disconnect the hose from the vacuum.
(Fig. 2)
3. Undo the latches and remove the power
head from the collection tank. (Fig. 3)
Place power head on a soft, clean
surface upside down.
4. Clear all dirt or debris from the collection
tank and hose into a proper waste
container. (Fig. 4)
5. Clean or replace the fi lters.
6. Check the hose, attachments, and
power cord to verify that they have not
been damaged.
1. Verify that the power cord is
disconnected from the outlet. (fi g. 1)
2. Remove the four screws holding the
intake shield and lift off the shield. (fi g. 2)
3. Remove the foam pad from the blower
and clean the foam pad with soapy
water and allow to dry. (fi g. 3)
disconnected from the outlet. (fi g. 1)
2. Remove the four screws holding the
intake shield and lift off the shield. (fi g. 2)
3. Remove the foam pad from the blower
and clean the foam pad with soapy
water and allow to dry. (fi g. 3)
After using the blower, examine the bottom of the blower for debris and blockages and
remove if found. To clean the foam pad of the intake:
remove if found. To clean the foam pad of the intake:
NOTICE! The fi lter included is made of
high quality material designed to stop small
dust particles. The fi lter should be used for
dry pick-up only. A dry fi lter is necessary
to pick up dust. If the dust fi lter is wet, it
will clog quickly and be very diffi cult to
clean. Handle the fi lter carefully when
removing it for cleaning and replacing it.
Check the fi lters for tears or small holes; a
small hole can let dust pass through and
out of the cleaner. Do not use a fi lter with
holes or tears; replace it immediately.
high quality material designed to stop small
dust particles. The fi lter should be used for
dry pick-up only. A dry fi lter is necessary
to pick up dust. If the dust fi lter is wet, it
will clog quickly and be very diffi cult to
clean. Handle the fi lter carefully when
removing it for cleaning and replacing it.
Check the fi lters for tears or small holes; a
small hole can let dust pass through and
out of the cleaner. Do not use a fi lter with
holes or tears; replace it immediately.
4. Check the foam pad for reuse. If you
need to replace the foam pad consult
the parts list of the manual.
5. Replace the foam pad on to the blower
aligning the wholes to the screw tabs.
(fi g. 4)
6. Reinstall the intake shield and the four
screws. (fi g. 5)
need to replace the foam pad consult
the parts list of the manual.
5. Replace the foam pad on to the blower
aligning the wholes to the screw tabs.
(fi g. 4)
6. Reinstall the intake shield and the four
screws. (fi g. 5)
4
1
2
3
3
4
5
2
7. Place power head on collection tank and
secure latches.
secure latches.
WARNING: Always disconnect the plug from the power outlet before
removing the power head from the container.
removing the power head from the container.
!