Cisco Cisco Aironet 1240 AG Access Point Notas de publicación
12
Release Notes for Cisco Aironet Access Points and Bridges for Cisco IOS Release 12.4(10b)JA1
OL-15533-01
Important Notes
Non-Cisco Aironet 802.11g Clients Might Require Firmware Upgrade
Some non-Cisco Aironet 802.11g client devices require a firmware upgrade before they can associate to
the 802.11g radio in the access point. If your non-Cisco Aironet 802.11g client device does not associate
to the access point, download and install the latest client firmware from the manufacturer’s website.
the 802.11g radio in the access point. If your non-Cisco Aironet 802.11g client device does not associate
to the access point, download and install the latest client firmware from the manufacturer’s website.
Throughput Option for 802.11g Radio Blocks Association by 802.11b Clients
When you configure the 802.11g access point radio for best throughput, the access point sets all data
rates to basic (required). This setting blocks association from 802.11b client devices. The best
throughput option appears on the web-browser interface Express Setup and Radio Settings pages and
in the speed CLI configuration interface command.
rates to basic (required). This setting blocks association from 802.11b client devices. The best
throughput option appears on the web-browser interface Express Setup and Radio Settings pages and
in the speed CLI configuration interface command.
Use Auto for Ethernet Duplex and Speed Settings
We recommend that you use auto, the default setting, for both the speed and duplex settings on the access
point Ethernet port. When your access point receives inline power from a switch, any change in the speed
or duplex settings that resets the Ethernet link reboots the access point. If the switch port to which the
access point is connected is not set to auto, you can change the access point port to half or full to correct
a duplex mismatch, and the Ethernet link is not reset. However, if you change from half or full back to
auto, the link is reset, and, if your access point receives inline power from a switch, the access point
reboots.
point Ethernet port. When your access point receives inline power from a switch, any change in the speed
or duplex settings that resets the Ethernet link reboots the access point. If the switch port to which the
access point is connected is not set to auto, you can change the access point port to half or full to correct
a duplex mismatch, and the Ethernet link is not reset. However, if you change from half or full back to
auto, the link is reset, and, if your access point receives inline power from a switch, the access point
reboots.
Note
The speed and duplex settings on the access point Ethernet port must match the Ethernet settings
on the port to which the access point is connected. If you change the settings on the port to which
the access point is connected, change the settings on the access point Ethernet port to match.
on the port to which the access point is connected. If you change the settings on the port to which
the access point is connected, change the settings on the access point Ethernet port to match.
Use force-reload Option with archive download-sw Command
When you upgrade access point or bridge system software by entering the archive download-sw
command on the CLI, you must use the force-reload option. If the access point or bridge does not reload
the flash memory after the upgrade, the pages in the web-browser interface might not reflect the upgrade.
This example shows how to upgrade system software by using the archive download-sw command:
command on the CLI, you must use the force-reload option. If the access point or bridge does not reload
the flash memory after the upgrade, the pages in the web-browser interface might not reflect the upgrade.
This example shows how to upgrade system software by using the archive download-sw command:
AP# archive download-sw /force-reload /overwrite tftp://10.0.0.1/image-name
Radio MAC Address Appears in ACU
When a Cisco Aironet client device associates to an access point running IOS software, the access point
MAC address that appears on the Status page in the Aironet Client Utility (ACU) is the MAC address
for the access point radio. The MAC address for the access point Ethernet port is printed on the label on
the back of the access point.
MAC address that appears on the Status page in the Aironet Client Utility (ACU) is the MAC address
for the access point radio. The MAC address for the access point Ethernet port is printed on the label on
the back of the access point.