Cisco Cisco UCS B200 M2 Blade Server Libro blanco
To display the NPIV status for all switch ports, issue the
portcfgshow command from the Brocade command-line
interface (CLI):
Brocade-A:admin> portcfgshow
Ports of Slot 0
0
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15
-----------------+---+--+---+--+--+---+--+--+--+---+---+--+--+---+--+---
Speed
AN AN AN AN AN AN AN AN AN AN AN AN AN AN AN AN
Fill Word
3
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
(On Active)
Fill Word
3
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
(Current)
AL_PA Offset 13
.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
Trunk Port
ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON
Long Distance
.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
VC Link Init
.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
Locked L_Port
.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
Locked G_Port
.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
Disabled E_Port
.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
Locked E_Port
.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
ISL R_RDY Mode
.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
RSCN Suppressed
.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
Persistent Disable .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
LOS TOV enable
.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
NPIV capability
ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON
NPIV PP Limit
126
126
126
126
126
126
126
126
126
126
126
126
126
126
126
126
The “NPIV capability” parameter will display as ON if the NPIV feature is enabled per port. The “NPIV PP Limit” parameter
displays the maximum virtual N_port IDs that can be configured on a per-port basis. The default is 126, and this value can
be set to from 1 to 255 per port.
displays the maximum virtual N_port IDs that can be configured on a per-port basis. The default is 126, and this value can
be set to from 1 to 255 per port.
Configure Cisco UCS and Brocade 8-Gbps Fibre Channel Fill Pattern
The following configurations are applicable when the Cisco UCS to Brocade FC connections are set to 8 Gbps. Failure to set
the correct Fibre Channel fill pattern can result in interoperability issues between the Cisco UCS fabric interconnects and
Brocade Fibre Channel switches. For additional information, refer to the Brocade Fabric OS Command Reference Manual.
the correct Fibre Channel fill pattern can result in interoperability issues between the Cisco UCS fabric interconnects and
Brocade Fibre Channel switches. For additional information, refer to the Brocade Fabric OS Command Reference Manual.
Configuring the Brocade Fibre Channel Fill Pattern
To display the current Brocade Fibre Channel fill pattern, use the portcfgshow command:
To display the current Brocade Fibre Channel fill pattern, use the portcfgshow command:
The default setting is mode 0, -idle-idle.
Brocade-A:admin> portcfgshow 0
Area Number:
0
Speed Level
AUTO(HW)
Fill Word(On Active) 0(Idle-Idle)
Fill Word(Current)
0(Idle-Idle)
.
.
7 © 2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public.