Cisco Cisco MDS 9000 NX-OS Software Release 4.1 Guía De Instalación
S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m .
13
Cisco MDS 9000 Family Storage Services Interface Image Installation and Upgrade Guide
OL-17262-03, Cisco MDS NX-OS Release 4.x
Cisco MDS 9000 Family Storage Services Interface Image Installation and Upgrade Guide
Upgrading to Cisco MDS NX-OS Release 4.1(1b) and Later From Earlier SAN-OS Releases
switch# copy running-config startup-config
Upgrading to Cisco MDS NX-OS Release 4.1(1b) and Later From
Earlier SAN-OS Releases
Earlier SAN-OS Releases
This section describes the guidelines to upgrade to Cisco MDS NX-OS Release 4.1(1b):
•
The procedure to upgrade to Cisco MDS NX-OS Release 4.1(1b) and later is same as release 3.0(1)
or later, in addition to the guidelines discussed in this section. For the general procedure, see the
or later, in addition to the guidelines discussed in this section. For the general procedure, see the
.
•
To upgrade to Cisco MDS NX-OS SSI image Release 4.1(1b), an SSM must be running SAN-OS
SSI image Release 3.3(1a) or 3.3(1c), or should not be running on an SSI image.
SSI image Release 3.3(1a) or 3.3(1c), or should not be running on an SSI image.
Note
As of Cisco MDS NX-OS Release 4.1(1b), when there are multiple SSM or MSM-18/4
modules in the same chassis, you can set the amount of time to delay between SSM or
MSM-18/4 modules in a rolling SSI upgrade. For more information, refer to the Cisco MDS
9000 Family Configuration Guides for Release 4.x.
modules in the same chassis, you can set the amount of time to delay between SSM or
MSM-18/4 modules in a rolling SSI upgrade. For more information, refer to the Cisco MDS
9000 Family Configuration Guides for Release 4.x.
•
If the module was running an SSI image, clear the SSI bootvar on the MSM-18/4, and MDS 9222i
module 1 modules before you upgrade to Cisco MDS NX-OS Release 4.1(1b) or later.
module 1 modules before you upgrade to Cisco MDS NX-OS Release 4.1(1b) or later.
•
If you have an SSM module running on an SSI image, then perform the following operations to
upgrade the MDS NX-OS and the SSI image on the SSM module:
upgrade the MDS NX-OS and the SSI image on the SSM module:
switch# install all system bootflash:m9500-sf1ek9-mz.4.1.1a.bin kickstart
bootflash:m9500-sf1ek9-kickstart-mz.4.1.1a.bin ssi bootflash:
m9000-ek9-ssi-mz.4.1.1a.bin
Caution
The install all command with the ssi option will upgrade the SSI image on an SSM not
running the specified SSI image.
The install all command with the ssi option will not upgrade the SSI image on an MSM-18/4
for a system running on MDS SAN-OS release earlier than 3.3(1c).
The install all command does not disrupt traffic on the Cisco MDS 9222i switches.
running the specified SSI image.
The install all command with the ssi option will not upgrade the SSI image on an MSM-18/4
for a system running on MDS SAN-OS release earlier than 3.3(1c).
The install all command does not disrupt traffic on the Cisco MDS 9222i switches.
•
If you do not have an SSM module running SSI image, or have only MSM-18/4 modules, or have an
SSM running SAN-OS Release 3.3(1c) compatible SSI image and you do not want to upgrade the
SSI image but upgrade only the NX-OS image, then perform the following operations:
SSM running SAN-OS Release 3.3(1c) compatible SSI image and you do not want to upgrade the
SSI image but upgrade only the NX-OS image, then perform the following operations:
switch# install all system bootflash:m9500-sf1ek9-mz.4.1.1a.bin kickstart
bootflash:m9500-sf1ek9-kickstart-mz.4.1.1a.bin
•
To install an SSI image on an SSM, MSM-18/4, or MDS 9222i module 1 on a switch running MDS
NX-OS Release 4.1(1b), perform the following operations:
NX-OS Release 4.1(1b), perform the following operations:
–
Use the install ssi command to install a new MDS NX-OS Release 4.1(1b) compatible SSI
image on an SSM module.
image on an SSM module.
switch# install ssi bootflash:m9000-ek9-ssi-mz.4.1.1a.bin module 2
–
Use the install all command with the ssi option to install a new MDS NX-OS Release 4.1(1b)
compatible SSI image on an SSM, MSM-18/4, and MDS 9222i module 1 modules.
compatible SSI image on an SSM, MSM-18/4, and MDS 9222i module 1 modules.