Cisco Cisco IPS 4255 Sensor Notas de publicación
![Cisco](https://files.manualsbrain.com/attachments/7380d0050044647c30f5c24bbbf5d0c0b6d9bb84/common/fit/150/50/faa183d287233c52228cfea3dbc2a127fe780f60564fcb0955d9c3d1cd23/brand_logo.png)
17
Release Notes for Cisco Intrusion Prevention System 6.0(6)E3
OL-20113-01
Upgrading to Cisco IPS 6.0(6)E3
Caution
Do not remove power to the IDS 4215 during the update process, otherwise the upgrade can get
corrupted. If this occurs, the IDS 4215 will be unusable and require an RMA.
corrupted. If this occurs, the IDS 4215 will be unusable and require an RMA.
For More Information
•
For a list of supported TFTP servers, see
.
•
For the procedure for locating software on Cisco.com, see
.
Upgrading to Cisco IPS 6.0(6)E3
This section provides information on upgrading to IPS 6.0(6)E3, and contains the following topics:
•
•
•
Upgrade Notes and Caveats
The following upgrade notes and caveats apply to upgrading to 6.0(6)E3:
•
The sensor must report its version as 5.1(5) or later for you to apply the 6.0(6)E3 service pack.
•
When you upgrade AIM-IPS, you must disable heartbeat reset on the router before installing an
upgrade. You can reenable heartbeat reset after you complete the upgrade. If you do not disable
heartbeat reset, the upgrade can fail and leave AIM-IPS in an unknown state, which may require a
system reimage to recover.
upgrade. You can reenable heartbeat reset after you complete the upgrade. If you do not disable
heartbeat reset, the upgrade can fail and leave AIM-IPS in an unknown state, which may require a
system reimage to recover.
•
If you try to upgrade a 5.1(5) sensor to 6.0(6)E3, you may receive an error that Analysis Engine is
not running:
not running:
sensor# upgrade scp://user@10.1.1.1/upgrades/IPS-K9-6.0-6-E3.pkg
Password: ********
Warning: Executing this command will apply a major version upgrade to the application
partition. The system may be rebooted to complete the upgrade.
Continue with upgrade?: yes
Error: Analysis Engine is not running. Please reset box and attempt upgrade again.
If you receive this error, you must get Analysis Engine running before trying to upgrade again. This
error is often caused by a defect in the currently running version. Try rebooting the sensor, and after
reboot, run the setup command and remove the interfaces from the virtual sensor vs0. When it is not
monitoring traffic, Analysis Engine usually stays up and running. You can upgrade to 6.0(6)E3 at
this time. After the upgrade to IPS 6.0(6)E3, add the interfaces back to the virtual sensor vs0 using
the setup command.
error is often caused by a defect in the currently running version. Try rebooting the sensor, and after
reboot, run the setup command and remove the interfaces from the virtual sensor vs0. When it is not
monitoring traffic, Analysis Engine usually stays up and running. You can upgrade to 6.0(6)E3 at
this time. After the upgrade to IPS 6.0(6)E3, add the interfaces back to the virtual sensor vs0 using
the setup command.
Or you can use the recovery CD (if your sensor has a CD-ROM) or the system image file to reimage
directly to IPS 6.0(6)E3. You can reimage a 5.x sensor to 6.0(6)E3 because the reimage process does
not check to see if Analysis Engine is running.
directly to IPS 6.0(6)E3. You can reimage a 5.x sensor to 6.0(6)E3 because the reimage process does
not check to see if Analysis Engine is running.