Cisco Cisco Aironet 1130 AG Access Point Notas de publicación
18
Release Notes for Cisco Aironet Access Points for Cisco IOS Release 12.3(8)JEA
OL-11186-01
Caveats
WLSM Required for Layer 3 Mobility
You must use a Wireless LAN Services Module (WLSM) as your WDS device in order to properly
configure Layer 3 mobility. If you enable Layer 3 mobility for an SSID and your WDS device does not
support Layer 3 mobility, client devices cannot associate using that SSID.
configure Layer 3 mobility. If you enable Layer 3 mobility for an SSID and your WDS device does not
support Layer 3 mobility, client devices cannot associate using that SSID.
Caveats
This section lists open and resolved caveats for access points.
Open Caveats
These caveats are open in Cisco IOS Release JA12.3(8)JEA:
•
CSCsa94560—GA: power save client deauthenticated before receiving EAP FAILURE message
A client that fails EAP authentication due to a bad username or password may show the reason to
be EAP timeout instead. This occurs only for clients in power save mode that remain in power save
mode when trying to authenticate. Also, either the username or password that the client is using to
authenticate must be incorrect.
be EAP timeout instead. This occurs only for clients in power save mode that remain in power save
mode when trying to authenticate. Also, either the username or password that the client is using to
authenticate must be incorrect.
Workaround: To check if the EAP authentication failure is caused by this caveat, change the client
configuration so it is no longer in power save mode. If the reason for the client failure is now an EAP
failure, correct the username or password. Once the username or password is corrected the client can
be reconfigured back to power save mode.
configuration so it is no longer in power save mode. If the reason for the client failure is now an EAP
failure, correct the username or password. Once the username or password is corrected the client can
be reconfigured back to power save mode.
•
CSCsb00606—350 series access points reload every couple of weeks
•
CSCsb84696—WLSE access point radio scan shows occasional SNMP timeouts
An access point radio scan on an 1100 series access point running Cisco IOS Release 12.3(4)JA may
occasionally fail because the WLSE is not able to set the Dot11RadioDiagTempTxPowerLevel on
the AP. The request times out with an “ERROR: AP not SNMP accessible” error.
occasionally fail because the WLSE is not able to set the Dot11RadioDiagTempTxPowerLevel on
the AP. The request times out with an “ERROR: AP not SNMP accessible” error.
Workaround: none.
•
CSCse59670—1200 series access point D0 radio fails and returns a cmd21 error message
While running the reboot test, after multiple successful reboot cycles, the d0 radio fails to startup
properly and displays a cmd21 error message:
properly and displays a cmd21 error message:
Mar 1 00:00:04.096: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test
passed
*Mar 1 00:00:04.437: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 1 00:00:05.297: %DOT11-2-RADIO_FAILED: Interface Dot11Radio0, failed - Radio
command failed, cmd 21 (FF00,0,0) status 7F21 (21,0,0)
•
CSCse84112—Access point passes data to client before authentication is completed
A 1200 series access point running Cisco IOS Release 12.3(8)JA sends encrypted RTP packets to a
7921 phone before the 802.1x EAP-FAST authentication is complete.
7921 phone before the 802.1x EAP-FAST authentication is complete.
•
CSCsd62033—MFP2 - Firmware strips IV fields from inbound management frames
AMAC firmware strips the IV and extIV fields (if present) from inbound management frames
preventing them from being processed by the driver.
preventing them from being processed by the driver.