Cisco Cisco Aironet 2600e Access Point Guía De Instalación
8
Note
CAPWAP support is provided in controller software release 5.2 or later. However, your controller must be running
release 7.2.110.0 or later to support 2600 series access points.
release 7.2.110.0 or later to support 2600 series access points.
Note
You cannot edit or query any access point using the controller CLI if the name of the access point contains a space.
Note
Make sure that the controller is set to the current time. If the controller is set to a time that has already occurred, the
access point might not join the controller because its certificate may not be valid for that time.
access point might not join the controller because its certificate may not be valid for that time.
Access points must be discovered by a controller before they can become an active part of the network. The access point supports
these controller discovery processes:
these controller discovery processes:
•
Layer 3 CAPWAP discovery—Can occur on different subnets than the access point and uses IP addresses and UDP packets
rather than MAC addresses used by Layer 2 discovery.
rather than MAC addresses used by Layer 2 discovery.
•
Over-the-air provisioning (OTAP)—This feature is supported by Cisco 4400 series controllers. If this feature is enabled on
the controller, all joined access points transmit wireless CAPWAP neighbor messages, and new access points receive the
controller IP address from these messages. This feature is disabled by default and should remain disabled when all access
points are installed.
the controller, all joined access points transmit wireless CAPWAP neighbor messages, and new access points receive the
controller IP address from these messages. This feature is disabled by default and should remain disabled when all access
points are installed.
Additional information about OTAP is available on Cisco.com at the following link:
•
Locally stored controller IP address discovery—If the access point was previously joined to a controller, the IP addresses of
the primary, secondary, and tertiary controllers are stored in the access point’s non-volatile memory. This process of storing
controller IP addresses on an access point for later deployment is called priming the access point. For more information
about priming, see the
the primary, secondary, and tertiary controllers are stored in the access point’s non-volatile memory. This process of storing
controller IP addresses on an access point for later deployment is called priming the access point. For more information
about priming, see the
•
DHCP server discovery—This feature uses DHCP option 43 to provide controller IP addresses to the access points. Cisco
switches support a DHCP server option that is typically used for this capability. For more information about DHCP option
43, see the
switches support a DHCP server option that is typically used for this capability. For more information about DHCP option
43, see the
.
•
DNS discovery—The access point can discover controllers through your domain name server (DNS). For the access point
to do so, you must configure your DNS to return controller IP addresses in response to
CISCO-CAPWAP-CONTROLLER.localdomain, where localdomain is the access point domain name. Configuring the
CISCO-CAPWAP-CONTROLLER provides backwards compatibility in an existing customer deployment. When an access
point receives an IP address and DNS information from a DHCP server, it contacts the DNS to resolve
CISCO-CAPWAP-CONTROLLER.localdomain. When the DNS sends a list of controller IP addresses, the access point
sends discovery requests to the controllers.
to do so, you must configure your DNS to return controller IP addresses in response to
CISCO-CAPWAP-CONTROLLER.localdomain, where localdomain is the access point domain name. Configuring the
CISCO-CAPWAP-CONTROLLER provides backwards compatibility in an existing customer deployment. When an access
point receives an IP address and DNS information from a DHCP server, it contacts the DNS to resolve
CISCO-CAPWAP-CONTROLLER.localdomain. When the DNS sends a list of controller IP addresses, the access point
sends discovery requests to the controllers.
Preparing the Access Point
Before you mount and deploy your access point, we recommend that you perform a site survey (or use the site planning tool) to
determine the best location to install your access point.
determine the best location to install your access point.
You should have the following information about your wireless network available:
•
Access point locations.
•
Access point mounting options: below a suspended ceiling, on a flat horizontal surface, or on a desktop.
Note
You can mount the access point above a suspended ceiling but you must purchase additional mounting hardware:
See
See
for additional information.
•
Access point power options: power supplied by the recommended external power supply (Cisco AIR-PWR-B), a DC power
supply, PoE from a network device, or a PoE power injector/hub (usually located in a wiring closet).
supply, PoE from a network device, or a PoE power injector/hub (usually located in a wiring closet).