Cisco Cisco WAP2000 Wireless-G Access Point - PoE Guía De Instalación

Cisco Systems, Inc.

170 West Tasman Drive

San Jose, CA 95134-1706
USA

http://www.cisco.com

Tel: 408 526-4000

800 553-NETS (6387)

Fax: 408 527-0883

Cisco, Cisco Systems, the Cisco logo, and the Cisco Systems logo are registered trademarks or trademarks of Cisco Systems,
Inc. and/or its affiliates in the United States and certain other countries. All other trademarks mentioned in this document or
Website are the property of their respective owners. The use of the word partner does not imply a partnership relationship
between Cisco and any other company. (0705R)

© 2009 Cisco Systems, Inc. All rights reserved. 

Printed in the USA on recycled paper containing 10% postconsumer waste.

78-19136-01

Line up the WAP2000 so that the wall-mount slots on the bottom of the 
access point line up with the two screws.

Place the wall-mount slots over the screws and slide the access point 
down until the screws fit snugly into the wall-mount slots.

You can connect the WAP2000 to your network in one of the following ways:

• Using a PoE router or switch

• Using a standard router or switch

To connect the WAP2000 to your network using a PoE router or switch, use the 
supplied Ethernet cable to connect the Ethernet port of the access point to a 
PoE port on the PoE router or switch.

The LEDs on the front panel light up as soon as the WAP2000 powers on.

To connect the WAP2000 to your network using a standard switch, follow these 
steps.

Use the supplied Ethernet cable to connect the Ethernet port of the 
access point to an Ethernet port on the router or switch.

Connect the included power adapter to the Power port of the 
WAP2000. 

Plug the power adapter into an electrical outlet. 

The LEDs on the front panel light up as soon as the WAP2000 powers on.

To verify the hardware installation, complete the following tasks:

• Check the cable connections.

• Check the LED states, as described in 

.

If you need help resolving a problem, visit the Cisco Small Business 
Support Community at 

. For 

technical documentation and other links, see 

The firmware v2.0.3.4 or later releases changed the factory default IP address 
configuration to DHCP. Before installation, make sure your DHCP server is 
running and can be reached. You may need to disconnect and reconnect the 
devices for them to discover their new IP addresses from the DHCP server.

If the WAP2000 access point does not receive a DHCP response after 60 
seconds, it falls back to the following default static IP address: 192.168.1.245 
and a default mask of 255.255.255.0.

To configure the access point, follow these steps to access the device’s web-
based configuration utility from your computer.

Connect the WAP2000 Access Point to the same network as your 
computer. 

Locate the IP address of the WAP2000 Access Point by accessing 
your DHCP server. Specific instructions on locating the DHCP address 
given to the WAP2000 Access Point depends upon the type of 
architecture and operating system you are using. Use your computer’s 
local Help and Support functionality and search for “IP Addressing”.

Launch a web browser, such as Internet Explorer or Mozilla Firefox.

In the Address field enter the default DHCP address and press the 
Enter key.

In the User Name and Password fields enter the default of admin. 

Click OK. 

Congratulations, you are now ready to begin using your WAP2000. You may 
wish to consider taking some of the following steps:

• Change the default password of the access point to protect it from 

unauthorized use.

• Depending on your deployment requirements, you might need to change 

some of the configuration parameters of the access point.

• Update the firmware version.

• For more information on how to change the password and configure the 

access point, refer to the 

Cisco WAP2000 Wireless-G Access Point with 

Power Over Ethernet Administration Guide

. This guide is on the CD-ROM 

that comes with the product. You can also access this guide and other 
related documentation on Cisco.com, as indicated in the next section.

Cisco Small Business Support 
Community

Online Technical Support and 
Documentation (Login Required)

Phone Support Contacts

Software Downloads
(Login Required)

Go to 

, 

and enter the model number in the Software 
Search box.

Cisco WAP2000 Wireless-G 
Access Point with Power Over 
Ethernet

Cisco Partner Central for Small 
Business (Partner Login 
Required)

Cisco Small Business Home

Marketplace