Cisco Cisco 1 GHz GainMaker Amplifier Hoja De Datos
Data Sheet
Page 8 of 9
Signal Directors
Signal directors are used in the High Gain Dual and Low Gain Dual system amplifiers only. One
signal director is required per amplifier to route and/or split forward RF signal to the Auxiliary output
port(s). The signal director is available in splitter, DC-8, or DC-12 configurations for splitting the
Auxiliary path signal to feed both Auxiliary ports, or as a jumper for routing all signals to a selected
port.
Table 12.
Signal Directors
– 1002 MHz (blue cover)
Type
Part
Number
Tap/
Thru
Leg
Typical Insertion Loss (dB) at Various Frequencies (MHz)
52
70
86
550
600
650
750
870
1002
Jumper
4008208
Aux 2
0.1
0.1
0.1
0.2
0.2
0.2
0.2
0.2
0.3
Aux 1
0.1
0.1
0.1
0.4
0.4
0.5
0.5
0.6
0.7
2-way
splitter
4008364
-
3.4
3.4
3.4
3.8
3.9
3.0
4.0
4.1
4.2
DC-8
4008365
Thru
1.7
1.8
1.8
2.1
2.1
2.1
2.1
2.2
2.3
Tap
8.3
8.3
8.3
8.2
8.3
8.2
8.1
8.0
8.0
DC-12
4008366
Thru
1.1
1.1
1.1
1.2
1.2
1.3
1.3
1.4
1.5
Tap
12.4
12.4
12.4
11.8
11.8
11.7
11.7
11.7
11.8
Table 13.
Signal Directors
– 870 MHz (blue cover)
Type
Part
Number
Tap/
Thru
Leg
Typical Insertion Loss (dB) at Various Frequencies (MHz)
52
70
86
550
600
650
750
870
Jumper
589281
-
0.1
0.1
0.1
0.2
0.2
0.2
0.3
0.3
2-way
splitter
589357
-
3.7
3.7
3.7
3.7
3.7
3.7
3.8
4.0
DC-8
589363
Thru
1.7
1.7
1.7
1.8
1.9
1.9
1.9
2.0
Tap
8.3
8.3
8.3
8.3
8.2
8.2
8.1
8.1
DC-12
589367
Thru
1.0
1.0
1.0
1.2
1.2
1.3
1.4
1.6
Tap
12.1
12.1
12.1
11.7
11.6
11.6
11.6
11.6
Note: The GainMaker plug-in signal director produces loss in the forward signal path only. The signal director
is physically located inboard of the forward/reverse diplex filters in the forward path of the amplifier. Therefore,
there are no reverse path losses associated. Auxiliary port reverse input pad values must be selected
accordingly during system design when using the splitter, DC-8, or DC-12 signal director in a station.
is physically located inboard of the forward/reverse diplex filters in the forward path of the amplifier. Therefore,
there are no reverse path losses associated. Auxiliary port reverse input pad values must be selected
accordingly during system design when using the splitter, DC-8, or DC-12 signal director in a station.
System Trim
A plug-in system trim may be used to counter the frequency response effects of some passive
devices in the coaxial plant. A mid frequency, single dip trim (Model MSD-1NGF) is available for all
870 MHz GainMaker amplifiers. The System Trim part number is 714446.
Table 14.
Fuse Kits /Surge Protectors
System Amplifier
Part Number
Slow Blow Fuse Kit, 4 amp (contains 4 fuses)
735628
Slow Blow Fuse Kit, 8 amp (contains 4 fuses)
735630
Slow Blow Fuse Kit, 15 amp (contains 4 fuses)
735632
Crowbar Surge Protector
715973