Sony DH280 Manual De Usuario

Ot
her

s

Using the SNMP

122

This unit supports SNMP (Simple Network 
Management Protocol). You can read MIB-2 objects 
using software such as SNMP manager software. This 
unit also supports the coldStart trap which occurs when 
the power is turned on or the unit restarts, and the 
Authentication failure trap, which informs of any illegal 
access using SNMP.
Using CGI commands, you can set the community name 
and access limitation, host to send traps, and some MIB-
2 objects. To allow these settings, you need 
authentication by the camera administrator.

You can check the SNMP Agent settings using the 
following CGI commands.

<Method>

GET, POST

<Command>

(JavaScript parameter format)

(standard format)

With the above inquiry, you can obtain the following 
setting information. The following explains the setting 
information using the inqjs=snmp (JavaScript 
parameter) format.

var sysDescr=“SNC-CH240” (or “SNC-CH140”, 

“SNC-DH140T”, “SNC-DH240T”,  “SNC-DH240”, 
“SNC-DH140”, “SNC-CH180”, “SNC-DH180”, 
“SNC-CH280”, “SNC-DH280”)

...1

var sysObjectID=“1.3.6.1.4.1.122.8501”

...2

var sysLocation=“”

...3

var sysContact=“”

...4

var sysName=“”

...5

var snmpEnableAuthenTraps=“1”

...6

var community=“1,r,public,0.0.0.0,v2c”

...7

var community=“2,r,private,192.168.0.101,v2c”

...8

var trap=“1,public,192.168.0.101,v2c”

...9

1

Describes the case of “mib-2.system. sysDescr.0”. 
You cannot change this parameter.

2

Describes the case of “mib-2.system. 
sysObjectID.0”. You cannot change this parameter.

3

Describes the case of “mib-2.system. 
sysLocation.0”. This field is used to describe 
information on the location of this camera. Nothing 
is set at the factory.

4

Describes the case of “mib-2.system. 
sysContact.0”. This field is used to describe 
information on the administrator of this camera. 
Nothing is set at the factory.

5

Describes the case of “mib-2.system. sysName.0”. 
This field is used to describe the administration 
node of this camera. Nothing is set at the factory.

6

Describes the case of “mib-2.snmpEnable 
AuthenTraps.0”. This example shows when “1” 
(enable) is set. In this setting, a trap occurs when 
there is an authentication failure. When “2” 
(disable) is set, no authentication failure trap 
occurs.

7

Describes the community attributes. This example 
shows the identification number “ID=1”, the 
community name “public”, and enables read from 
any IP address (0.0.0.0).

8

Describes the community attributes, similar to 7. 
This example shows the identification number 
ID=2, the community name “private”, and enables 
reading by SNMP request packet from the host 
“192.168.0.101”.

9

Describes the attributes to send a trap. This example 
shows the identification number “ID=1”, the 
community name “public”, and enables sending of 
traps to the host having the IP address 
“192.168.0.101”.

The unit supports the following SNMP setting 
commands.

<Method>

GET, POST

<Command>

First, perform the settings of the following parameters.

1)

sysLocation=<string>
Set the case of “mib-2.system.sysLocation.0” in the 
<string> position. The maximum length of <string> 
is 255 characters.

2)

sysContact=<string>
Set the case of “mib-2.system.sysContact.0” in the 
<string> position. The maximum length of <string> 
is 255 characters.