Panasonic dmr-es46v Manual De Usuario

, F

” stands for a number.)

≥An error has occurred. The number following “H” or “F” depends on the status of the unit. Check the 

items in the “Error messages” section and the “Troubleshooting guide”. If the service number still 
does not disappear after the check, follow the Reset procedure described below.
Reset procedure: (“The unit is on but cannot be operated.” 

l 69)

≥If the service numbers fail to clear, note the service numbers and contact a qualified service person.

–

–

 (“” stands for a number.) ≥The remote control and main unit are using different codes. Change the code on the remote control.

≥If there is no change after turning the unit on and off, consult the dealer where the unit was purchased.

–

≥The disc is dirty or badly scratched. The unit cannot record, play, or edit.

≥You have used a lens cleaner and it has finished. Press [<, OPEN/CLOSE] to eject the disc.

6, 10

≥Displayed when the unit is started. This is not a malfunction.

≥The unit is carrying out its recovery process. You cannot operate the unit while “PLEASE WAIT” is 

displayed.

–
–

≥There are already 16 scheduled recording programs. Delete unnecessary scheduled recording 

programs.

≥You have inserted a disc the unit cannot play or record on.

≥You have inserted a new DVD-RW/+R/+R DL/+RW or a DVD-RAM/DVD-RW (DVD-Video format) 

recorded on other equipment.

≥The HDMI connection could not be authenticated due to a transfer malfunction.

–

≥The HDMI connection could not be authenticated due to a internal data malfunction.

–

≥The unit is very warm.

The unit switches to standby for safety reasons. Wait for about 30 minutes until the message disappears.
Select a position with good ventilation when installing the unit. Do not block the cooling fan on the rear of the unit.

–

≥There was a power failure or the AC plug was disconnected while the unit was on. The unit is 

carrying out its recovery process. This process restores the unit to normal operation. The unit is not 
broken. Wait until the message disappears.

–

≥The connected equipment is not HDMI compatible.

–

≥The HDMI connection acts unusually.

- The connected equipment is not HDMI compatible.
- The HDMI cable is too long.
- The HDMI cable is damaged.

–

≥There was something unusual detected with the disc while recording, playing or transferring 

(copying), there was a power failure or the AC plug was disconnected while the unit was on. The unit 
is carrying out its recovery process. This process restores the unit to normal operation. The unit is not 
broken. Wait until the message disappears.

≥The unit fails to operate properly. Press [Í/I, POWER] on the main unit to switch the unit to standby. 

Now press [

Í/I, POWER] on the main unit again to turn the unit on.

–

≥The program was copy-protected.

≥The disc may be full.

≥There are already 99 recorded titles ([+R] [+R]DL] [+RW] 49 recorded titles).

–
–
–

≥You inserted an incompatible disc (Discs recorded in PAL video, etc.).

–

≥The disc may be dirty or scratched.

≥Create space by erasing any unwanted titles. [RAM] [-RW‹V›] [+RW]

[Even if you erase recorded content from the DVD-R or +R, there is no increase in disc space. Available 
recording space on a DVD-RW (DVD-Video format) or +RW increases when the last recorded title is 
deleted. (The recording space may increase slightly when other titles are deleted.)]

≥Use a new disc.

41, 59, 

–

≥Press [ENTER] to start recovery process. You cannot operate the unit while it is recovering 

(“SELF CHECK” appears on the unit’s display).

–

≥You haven’t inserted a disc. Correctly insert a disc that the unit can play.

≥The disc is upside down. If it is a single-sided disc, insert it so the label is facing up.

6, 10, 24

≥There is no compatible folder in this unit.

≥The card is not inserted. If this message is displayed with a compatible card already inserted, turn off 

the unit, remove and then re-insert the card.

≥The card inserted is not compatible or the card format does not match.

≥A video cassette is not inserted when recording programs. Insert a video cassette with an accidental 

erasure prevention tab.

11, 24

≥The VHS plays back while recording on DVD. You can watch the VHS playback by connect to the 

DVD/VHS COMMON terminals.

≥There may be a problem with the disc. Press [<, OPEN/CLOSE] on the main unit to remove it and 

check it for scratches or dirt. (The unit turns off automatically after you open the tray.)

≥The clock is not set when recording programs or setting the scheduled recording. Set the clock.

19, 22

≥A video cassette without the accidental erasure prevention tab is inserted when recording programs. Use a 

video cassette with an accidental erasure prevention tab.

≥The unit cannot record on the disc you inserted. Insert a DVD-RAM or unfinalized DVD-R, 

DVD-R DL, DVD-RW (DVD-Video format), +R, +R DL or +RW.

≥You inserted an unformatted DVD-RAM, DVD-RW, +R, +R DL or +RW. Format the disc with the unit.

–

≥The operation is prohibited by the unit, disc or cassette.

M6VP&PC.book  67 ページ  ２００６年２月６日　月曜日　午後３時２９分