Yamaha aw16g Manual De Usuario
167
Using the
A
W16G with e
xternal de
vices
15
Using external effects
As an alternative to using the internal effects, you can use
an external effect processor connected to the STEREO/
AUX OUT jacks. As an example, here’s how you can use
AUX bus 1 to apply a mono-in stereo-out reverb to the
track channels during mixdown.
an external effect processor connected to the STEREO/
AUX OUT jacks. As an example, here’s how you can use
AUX bus 1 to apply a mono-in stereo-out reverb to the
track channels during mixdown.
1
Lower the [STEREO] fader to the –
∞
position.
2
In the Selected Channel section, repeatedly
press the [PAN/BAL] knob or hold down the
[PAN/BAL] knob and use the CURSOR [
press the [PAN/BAL] knob or hold down the
[PAN/BAL] knob and use the CURSOR [
]/
[
] keys to access the AUX OUT page of the
PAN screen.
In this page you can select one of the following as
the signal that will be output from the STEREO/AUX
OUT jacks.
the signal that will be output from the STEREO/AUX
OUT jacks.
STEREO...................... Stereo bus (default)
AUX 1/2..................... AUX bus 1/2
AUX 1/2..................... AUX bus 1/2
3
Move the cursor to the AUX 1/2 button and
press the [ENTER] key.
press the [ENTER] key.
The AUX bus 1 signal will be output from the L
channel of the STEREO/AUX OUT jacks, and the
AUX bus 2 signal will be output from the R channel
of the STEREO/AUX OUT jacks.
channel of the STEREO/AUX OUT jacks, and the
AUX bus 2 signal will be output from the R channel
of the STEREO/AUX OUT jacks.
4
As shown in the following diagram, connect
your external effect processor to the AW16G.
your external effect processor to the AW16G.
Note
Note
If you make the above connection with the [STEREO]
fader raised before performing steps 2 and 3, oscillation
may occur. Please use caution.
fader raised before performing steps 2 and 3, oscillation
may occur. Please use caution.
5
Press the [PAN/BAL] knob twice to access the
AUX page of the PAN screen.
AUX page of the PAN screen.
1
AUX 1 knobs
Adjust the send level of the signals that are sent
from each channel to AUX bus 1.
from each channel to AUX bus 1.
B
PRE/POST (upper line)
Select the location from which the signal is sent
from each channel to AUX bus 1. Move the cursor
to the desired channel and press the [ENTER] key to
switch between the following two settings.
from each channel to AUX bus 1. Move the cursor
to the desired channel and press the [ENTER] key to
switch between the following two settings.
PRE (pre-fader) ...........The signal immediately before the
fader will be sent.
POST (post-fader).......The signal immediately after the
fader will be sent.
C
AUX2 knobs
Adjust the send level of the signals that are sent
from each channel to AUX bus 2.
from each channel to AUX bus 2.
D
PRE/POST (lower line)
Select the location from which the signal is sent
from each channel to AUX bus 2. Move the cursor
and press the [ENTER] key to switch between PRE
and POST.
from each channel to AUX bus 2. Move the cursor
and press the [ENTER] key to switch between PRE
and POST.
6
Raise the AUX knob 1 of each channel to an
appropriate level, and switch the PRE/POST
setting in the upper line as desired.
appropriate level, and switch the PRE/POST
setting in the upper line as desired.
With the settings so far, the signal from the track
channel will be sent from AUX bus 1 via the STE-
REO/AUX OUT jack to the internal effect.
channel will be sent from AUX bus 1 via the STE-
REO/AUX OUT jack to the internal effect.
7
Use the Quick Navigate section [RECORD]
key to access the MIXDOWN page of the
RECORD screen, and make the settings
shown below.
key to access the MIXDOWN page of the
RECORD screen, and make the settings
shown below.
With these settings, the unprocessed sound of track
channels 1–16 and the effect sound returned to
input channels 3/4 will be sent to the stereo bus and
mixed. You can monitor these signals via the MON-
ITOR OUT jacks.
channels 1–16 and the effect sound returned to
input channels 3/4 will be sent to the stereo bus and
mixed. You can monitor these signals via the MON-
ITOR OUT jacks.
AW16G
MIC/LINE
INPUT 3/4
STEREO/
AUX OUT (L)
AUX OUT (L)
MONITOR
OUT
OUT
Effect processor
34
21