Digidesign 2 Manual De Usuario
Chapter 7: Using Digi 002 as a Stand-Alone Mixer
83
Overview
When operating in Stand-alone Mode, Digi 002
is a 8x4x2 digital mixer, consisting of:
is a 8x4x2 digital mixer, consisting of:
• 8 inputs corresponding to Analog Inputs 1–8
on the Digi 002 back panel, controlled by the
eight channel strips on the top panel
eight channel strips on the top panel
• 4 available sends on each channel, for adding
internal Delay or Reverb effects, or for inte-
grating external effects processors
grating external effects processors
• Dedicated, in-line three-band EQ on input
channels 1–8
• Dedicated, in-line compressor on input chan-
nels 1–4
• A stereo output corresponding to Main Out-
puts 1–2 on the Digi 002 back panel
Digital Mixer Sample Rate
In Stand-alone mode, Digi 002 functions as a
digital mixer with a nominal sample rate of
44.1 kHz. Analog input signals are converted to
digital signals for processing and mixing.
digital mixer with a nominal sample rate of
44.1 kHz. Analog input signals are converted to
digital signals for processing and mixing.
In Stand-alone mode, Digi 002 supports digital
inputs at sample rates up to 48 kHz.
inputs at sample rates up to 48 kHz.
Mixer Inputs
Inputs 1–4
These inputs accept microphone-,
line-, or instrument-level signals, and provide
variable gain with the Input Gain control on the
Digi 002 top panel.
variable gain with the Input Gain control on the
Digi 002 top panel.
Phantom power is available to Inputs 1–4, in
channel pairs, using the Phantom Power
switches on the back panel of Digi 002.
channel pairs, using the Phantom Power
switches on the back panel of Digi 002.
Inputs 5–8
These inputs accept line-level signals
and are switchable between –10 dBV and +4 dBu
with the operating level switches on
theDigi 002 back panel.
with the operating level switches on
theDigi 002 back panel.
Alt Src Inputs
These inputs are active in Stand-
alone Mode, allowing you to connect and mon-
itor alternate audio sources such as CD players
or tape decks. The signal from the Alt Src Inputs
can be routed directly to the Monitor and Head-
phone Outputs (by pressing the Alt Src to Mon
switch) or to Input channels 7–8 (by pressing
the Alt Src to 7–8 switch).
itor alternate audio sources such as CD players
or tape decks. The signal from the Alt Src Inputs
can be routed directly to the Monitor and Head-
phone Outputs (by pressing the Alt Src to Mon
switch) or to Input channels 7–8 (by pressing
the Alt Src to 7–8 switch).
When Alt Src to 7–8 is enabled, analog inputs
7–8 (1/4-inch TRS connectors on the back panel
of Digi 002) are disabled.
7–8 (1/4-inch TRS connectors on the back panel
of Digi 002) are disabled.
S/PDIF Digital Inputs
In Stand-alone Mode, you
can activate these digital inputs so that they ap-
pear on inputs 5–6, allowing you to bring a ste-
reo digital signal into the Digi 002. (See “Digital
Audio Connections in Stand-Alone Mode” on
page 85.)
pear on inputs 5–6, allowing you to bring a ste-
reo digital signal into the Digi 002. (See “Digital
Audio Connections in Stand-Alone Mode” on
page 85.)
Sends
Each of the 8 channels of Digi 002 can send to
any or all of the four available sends at the same
time. Sends can be either pre- or post-fader.
any or all of the four available sends at the same
time. Sends can be either pre- or post-fader.
Send A
Routes the input signal to the internal
Delay processor
Send B
Routes the input signal to the internal
Reverb processor
Send C
Routes the input signal to output 7 on
the back panel of Digi 002
Send D
Routes the input signal to output 8 on
the back panel of Digi 002
In Stand-alone mode, Digi 002 will not op-
erate correctly with an external clock source
greater than 48 kHz.
erate correctly with an external clock source
greater than 48 kHz.
All the send assignments in Stand-alone
mode are fixed, and cannot be changed.
mode are fixed, and cannot be changed.