Cisco Systems 2600 Manual De Usuario
Caller ID on Cisco 2600 and 3600 Series Routers and Cisco MC3810 Multiservice Concentrators
Caller ID Configuration Task List
VC-816
Cisco IOS Voice, Video, and Fax Configuration Guide
The following table lists the options that may be used for the locale variable with the cptone command.
Step 3
Router(config-voiceport)# voice confirmation-tone
Enables the two-beep confirmation tone that a
caller hears when picking up the handset, if
connection plar or connection plar-opx is
configured.
caller hears when picking up the handset, if
connection plar or connection plar-opx is
configured.
Step 4
Router(config-voiceport)# dial-type {dtmf | pulse}
(For FXO ports only) Selects the appropriate dial
type for out-dialing.
type for out-dialing.
Step 5
Router(config-voiceport)# signal {loop-start |
ground-start
}
Selects the appropriate signal type for this
interface.
interface.
Step 6
Router(config-voiceport)# codec {g729r8 | g729ar8 |
g726r32
| g711alaw | g711ulaw}
(Cisco MC3810 multiservice concentrator only)
Configures the voice-port compression mode. The
g729ar8 value is the default and is recommended.
Configures the voice-port compression mode. The
g729ar8 value is the default and is recommended.
Note
On Cisco 2600 and 3600 series routers,
codec configuration is performed on dial
peers. On all supported routers, codec
command options may vary depending
upon the voice card settings.
codec configuration is performed on dial
peers. On all supported routers, codec
command options may vary depending
upon the voice card settings.
Step 7
Router(config-voiceport)# cptone locale
Selects the appropriate voice call progress tone for
this interface. Caller ID requires this setting. The
caller ID standard (Bellcore/Telcordia, ETSI,
ETSI-DTMF) is determined by this command.
this interface. Caller ID requires this setting. The
caller ID standard (Bellcore/Telcordia, ETSI,
ETSI-DTMF) is determined by this command.
On the Cisco MC3810 multiservice concentrator,
the default setting for locale is northamerica. On
Cisco 2600 and 3600 series routers, the default
setting for locale is us.
the default setting for locale is northamerica. On
Cisco 2600 and 3600 series routers, the default
setting for locale is us.
for a list of options.
Step 8
Router(config-voiceport)# ring frequency {25 | 50}
(Required on Cisco 2600 and 3600 series routers
FXS ports only) Selects the appropriate ring
frequency (in hertz) specific to the equipment
attached to this voice port.
FXS ports only) Selects the appropriate ring
frequency (in hertz) specific to the equipment
attached to this voice port.
Step 9
Router(config-voiceport)# caller-id attenuation
attenuation
(Optional on FXO ports only) Specifies an
attenuation other than the default of 14 dB (minus
14 dBm), enter a value of from 0 to 64, in decibels.
attenuation other than the default of 14 dB (minus
14 dBm), enter a value of from 0 to 64, in decibels.
Step 10
Router(config-voiceport)# ring number number
(Required on Cisco 2600 and 3600 series routers
FXO ports only) Specifies the maximum number
of rings to be detected before answering a call.
FXO ports only) Specifies the maximum number
of rings to be detected before answering a call.
Command
Purpose
Table 57
cptone Command Entries for the Cisco 2600 and 3600 Series
Command Option
Country
Command Option
Country
ar
Argentina
lu
Luxembourg
au
Australia
my
Malaysia
at
Austria
mx
Mexico
be
Belgium
nl
Netherlands