Shenzhen Aodee Electronic Co. Ltd. AODEE0AT258 Manual De Usuario
1
INDOOR SUPER SWITCH PRO
Wireless Remote Control Wall Outlet
Set of 3 Indoor Outlets and Remote Control
Package Includes:
Package Includes:
(3) Wireless Wall Outlet Receivers (Receiver Unit)
(1) 4- Button Hand-Held Remote Control (Sender Unit)
(1) 12V Type 23A battery
(1) 4- Button Hand-Held Remote Control (Sender Unit)
(1) 12V Type 23A battery
Features:
The Super Switch operates on radio frequency and is not dependent on line of sight and will perform through
walls, doors and floors up to 100 feet away. No rewiring is required.
walls, doors and floors up to 100 feet away. No rewiring is required.
Operation:
Remove Tape From Battery Chamber.
Remove battery cover on Hand-Held Remote Control unit and remove protective tape. Re-install battery cover.
Plug in Receiver Units.
Plug the individual wall receiver unit into any standard indoor wall outlet.
Operation and Safety.
Use only 1 Super Switch Receiver per AC outlet. A distance of 24 inches should be maintained between
individual receiver units. Do not overload individual Super Switch receiver unit beyond 1000 watts. Maximum
output load: 125V/60Hz/8A. FOR INDOOR USE ONLY.
Receiver Unit Function.
ON/OFF Buttons. The power control button on the front of the wall receiver unit is used to manually power the
wall receiver ON when pressed and OFF when pressed again. The unit can also be powered ON with the
hand-held remote control. The Red LED ON light on the front of the wall receiver unit will illuminate when
power is ON. If the Red LED (ON) does not illuminate check to be sure your indoor wall outlet is powered ON.
Remote Control Functions.
The Hand-Held Remote Control unit has a single Red LED indicator light that shows the radio signal has been
sent. The Hand-Held Remote Control features four buttons marked 1, 2, 3 and 4 respectively. Each button 1, 2,
3 corresponds to a specific wall receiver unit. Each of the individual receivers is clearly labeled 1, 2 or 3 to
correspond to the buttons on the Hand-Held Remote Control unit. Pressing the buttons on the Hand-Held
Remote Control turns the power ON or OFF at the corresponding receiver. Button 4 does not control any of
the wall receiver units included in the set, and is included on the remote control in the event you wish
to purchase additional Super Switch units and program them to be controlled from a single hand-held
remote control unit. In order to do so, see section below:
Remove battery cover on Hand-Held Remote Control unit and remove protective tape. Re-install battery cover.
Plug in Receiver Units.
Plug the individual wall receiver unit into any standard indoor wall outlet.
Operation and Safety.
Use only 1 Super Switch Receiver per AC outlet. A distance of 24 inches should be maintained between
individual receiver units. Do not overload individual Super Switch receiver unit beyond 1000 watts. Maximum
output load: 125V/60Hz/8A. FOR INDOOR USE ONLY.
Receiver Unit Function.
ON/OFF Buttons. The power control button on the front of the wall receiver unit is used to manually power the
wall receiver ON when pressed and OFF when pressed again. The unit can also be powered ON with the
hand-held remote control. The Red LED ON light on the front of the wall receiver unit will illuminate when
power is ON. If the Red LED (ON) does not illuminate check to be sure your indoor wall outlet is powered ON.
Remote Control Functions.
The Hand-Held Remote Control unit has a single Red LED indicator light that shows the radio signal has been
sent. The Hand-Held Remote Control features four buttons marked 1, 2, 3 and 4 respectively. Each button 1, 2,
3 corresponds to a specific wall receiver unit. Each of the individual receivers is clearly labeled 1, 2 or 3 to
correspond to the buttons on the Hand-Held Remote Control unit. Pressing the buttons on the Hand-Held
Remote Control turns the power ON or OFF at the corresponding receiver. Button 4 does not control any of
the wall receiver units included in the set, and is included on the remote control in the event you wish
to purchase additional Super Switch units and program them to be controlled from a single hand-held
remote control unit. In order to do so, see section below: