Shenzhen Aodee Electronic Co. Ltd. AODEE0AT258 Manual De Usuario
2
Programmable Function
The product has been pre-programmed for your convenience. The transmitter and receiver can be programmed
to different codes in the event that you wish to add additional transmitters or receivers to your set. This is
simply done by matching the Unit Code (1-16) and Master Code (A-P) to the respective units.
In order to add additional remotes and power stakes, FIRST match the dial on the remote and power stake to
the Master Code (A-P) of your choosing. Once synchronized, the corresponding buttons on the remote (1-4)
will match the respective power stakes. NEXT, tune the Unit Code (1-16) dial on the power stake to the
corresponding button on the remote: Button 1 controls all power stakes tuned to 1. Button 2 controls all power
stakes tuned to 2. Button 3 controls all power stakes tuned to 3. Button 4 controls all power stakes tuned to 4.
In order to sync even more power stakes, you can utilize the slide feature located in the battery casing of the
remote. First, slide the button located within the battery casing of the remote from “1-4” to “5-8”. This allows for
the user to control additional receivers that are synchronized. In order to do so, set the Unit Code (1-16) on the
additional power stakes to any number between “5-8”. Hence: Button 1 controls all power stakes tuned to 5.
Button 2 controls all power stakes tuned to 6. Button 3 controls all power stakes tuned to 7. Button 4 controls
all power stakes tuned to 8. For further clarification see diagram below:
The product has been pre-programmed for your convenience. The transmitter and receiver can be programmed
to different codes in the event that you wish to add additional transmitters or receivers to your set. This is
simply done by matching the Unit Code (1-16) and Master Code (A-P) to the respective units.
In order to add additional remotes and power stakes, FIRST match the dial on the remote and power stake to
the Master Code (A-P) of your choosing. Once synchronized, the corresponding buttons on the remote (1-4)
will match the respective power stakes. NEXT, tune the Unit Code (1-16) dial on the power stake to the
corresponding button on the remote: Button 1 controls all power stakes tuned to 1. Button 2 controls all power
stakes tuned to 2. Button 3 controls all power stakes tuned to 3. Button 4 controls all power stakes tuned to 4.
In order to sync even more power stakes, you can utilize the slide feature located in the battery casing of the
remote. First, slide the button located within the battery casing of the remote from “1-4” to “5-8”. This allows for
the user to control additional receivers that are synchronized. In order to do so, set the Unit Code (1-16) on the
additional power stakes to any number between “5-8”. Hence: Button 1 controls all power stakes tuned to 5.
Button 2 controls all power stakes tuned to 6. Button 3 controls all power stakes tuned to 7. Button 4 controls
all power stakes tuned to 8. For further clarification see diagram below:
The selector switch is located in the battery compartment. When set to 1-4, buttons 1-4 on the remote will
control power stakes with the dial tuned to 1-4. When the switch is set to 1-5, buttons 1-4 will control power
stakes with the dial tuned to 5-8.
Battery Replacement/Storage
Replacement: If operation of the wall receiver units becomes erratic, it may be necessary to replace the battery
in the hand-held remote sending unit. To do this, first remove the battery compartment cover. Next, remove
the depleted battery and discard according to local ordinances. Be sure to correctly reinstall the new battery.
The negative (-) end of the battery (marked on the battery label) is inserted into the battery compartment first
toward the spring marked with the negative (-) symbol inside the battery compartment. Slide positive (+) end of
battery down next into the battery compartment. Replace battery compartment cover. Replace with Type 23A
12V battery
Storage: If the hand-held remote control is to be stored and unused for an extended amount of time – 3 months
or longer; it is recommended that the battery be removed. Follow the instructions for battery replacement and
once removed, store the battery in a secure location. When the hand-held remote control is put back into use,
reinstall the battery. There is no guarantee for battery life. If reinstalled battery fails to operate units correctly,
user must replace battery with Type 23A 12V battery.
control power stakes with the dial tuned to 1-4. When the switch is set to 1-5, buttons 1-4 will control power
stakes with the dial tuned to 5-8.
Battery Replacement/Storage
Replacement: If operation of the wall receiver units becomes erratic, it may be necessary to replace the battery
in the hand-held remote sending unit. To do this, first remove the battery compartment cover. Next, remove
the depleted battery and discard according to local ordinances. Be sure to correctly reinstall the new battery.
The negative (-) end of the battery (marked on the battery label) is inserted into the battery compartment first
toward the spring marked with the negative (-) symbol inside the battery compartment. Slide positive (+) end of
battery down next into the battery compartment. Replace battery compartment cover. Replace with Type 23A
12V battery
Storage: If the hand-held remote control is to be stored and unused for an extended amount of time – 3 months
or longer; it is recommended that the battery be removed. Follow the instructions for battery replacement and
once removed, store the battery in a secure location. When the hand-held remote control is put back into use,
reinstall the battery. There is no guarantee for battery life. If reinstalled battery fails to operate units correctly,
user must replace battery with Type 23A 12V battery.