Lutron Electronics Company Inc 0108 Manual De Usuario
041467
Rev. A
07/2014
Part of the Energi TriPakR Family
Project 37 Load Control Module |
Programming
ALL PROGRAMMING IS OPTIONAL
Programming is not required for default functionality
• Set a favorite light level
• Set high-end and low-end trim for all fixtures
• Set a favorite light level
• Set high-end and low-end trim for all fixtures
Lutron Electronics Co., Inc., 7200 Suter Road
Coopersburg, PA 18036-1299 U.S.A.
Limited Warranty
Lutron EA Ltd. (“Lutron EA”) warrants each unit to be free from
defects in material and workmanship and to perform under
normal use and service. To the extent permitted by law, Lutron
EA and Lutron Electronics Co. Inc. (“Lutron”) make no warranties
or representations as to the units except as set forth herein. This
warranty shall run for a period of two years from the date of purchase
and Lutron’s obligations under this warranty are limited to remedying
any defect, replacing any defective part or replacement (at Lutron
EA’s sole option) and shall be effective only if the defective unit
is shipped to Lutron EA postage prepaid within 24 months after
purchase of the unit. Repair or replacement of the unit does not affect
the expiry date of the warranty. This warranty does not cover damage
or deficiencies due to abuse, misuse, inadequate wiring or insulation
or use or installation other than in accordance with instructions
accompanying the unit.
To the extent permitted by law, neither Lutron EA nor Lutron shall be
To the extent permitted by law, neither Lutron EA nor Lutron shall be
liable for any other loss or damage including consequential or special
loss or damages, loss of profits, loss of income, or loss of contracts
arising out of or relating to the supply of the unit or the use of the unit
and the purchaser assumes and will hold harmless Lutron EA and
Lutron in respect of all such loss or damage. Nothing in this warranty
shall have the effect of limiting or excluding Lutron EA’s or Lutron’s
liability for fraud or for death or personal injury resulting from its own
negligence, or any other liability, if and to the extent that the same
may not be limited or excluded as a matter of law.
This warranty does not affect the statutory rights of consumer
This warranty does not affect the statutory rights of consumer
purchasers of this product.
Although every attempt is made to ensure that catalogue information
Although every attempt is made to ensure that catalogue information
is accurate and up-to-date, please check with Lutron EA before
specifying or purchasing this equipment to confirm availability, exact
specifications, and suitability for your application.
For information on other products, please see the Warranty
For information on other products, please see the Warranty
enclosed with the product.
Lutron, Pico, PowPak, Energi TriPak, Clear Connect, EcoSystem,
Lutron, Pico, PowPak, Energi TriPak, Clear Connect, EcoSystem,
and ) are registered trademarks and Radio Powr Savr is a
trademark of Lutron Electronics Co., Inc.
©2014 Lutron Electronics Co., Inc.
©2014 Lutron Electronics Co., Inc.
Reset Factory Defaults
Note: In some instances, it may be necessary
to reset the PowPak
to reset the PowPak
®
Dimming Module and
connected devices back to factory default
settings. Before beginning, make sure that all
devices are connected and powered.
settings. Before beginning, make sure that all
devices are connected and powered.
A
Triple-tap any button on the PowPak
®
Dimming
Module and hold until the LED begins to flash
slowly; release button.
slowly; release button.
B
Within 3 seconds of the start of flashing, triple-tap
the same button again and the LEDs will flash
rapidly indicating that the unit has been reset to
factory defaults.
Note: Any associations or programming
previously set up with the PowPak
rapidly indicating that the unit has been reset to
factory defaults.
Note: Any associations or programming
previously set up with the PowPak
®
will be erased
and will need to be re-programmed.
5
Set Low-End and High-End Trim
For best results, minimize the amount of sunlight entering the room before performing the following procedures.
Low-End Trim
Low-End Trim
A Enter low-end trim adjustment mode:
Press and hold Lower button “ ” for 12 seconds.
Lights will flash high-low-high and LED will begin flashing.
Lights will flash high-low-high and LED will begin flashing.
B Adjust the low-end trim:
Use Raise button “ ” and Lower button “ ” to adjust and set the lights to the desired low-end (1 to 45%).
C Save the low-end trim:
Press and hold Toggle button “ ” for 6 seconds to save setting.
LED will begin flashing and then turn solid to indicate new level has been saved.
High-End Trim
LED will begin flashing and then turn solid to indicate new level has been saved.
High-End Trim
D Enter high-end trim adjustment mode:
Press and hold Raise button “ ” for 12 seconds.
Lights will flash high-low-high and LED will flash.
Lights will flash high-low-high and LED will flash.
E Adjust the high-end trim:
Use Raise button “ ” and Lower button “ ” to adjust and set the lights to the desired high-end
(55 to 100%).
(55 to 100%).
F Save the high-end trim:
Press and hold Toggle button “ ” for 6 seconds to save setting.
LED will begin flashing and then turn solid to indicate new level has been
LED will begin flashing and then turn solid to indicate new level has been
Notes
Depending on the fixture
Depending on the fixture
manufacturer or load, low-end
and high-end trim may need to
be adjusted.
• Trim low-end to ensure a stable
light level because some loads
will flicker or drop out if trimmed
too low.
• Be sure that you can turn on the
lights to the low-end trim level
without any abnormal operation.
• The factory default high-end trim
will normally be sufficient for most
applications. Trim as desired.
4
Raise
Lower
Favorite
Troubleshooting
www.lutron.com
Ballasts cannot be controlled locally from
PowPak
PowPak
®
Dimming Module.
• Ensure that the breaker(s) to the PowPak
®
Dimming Module are energized.
• Ensure that the PowPak
®
Dimming Module switched hot lead is wired to the ballast(s).
• Ensure that the PowPak
®
Dimming Module 0 –10 V control lines are wired to the ballast(s).
Reset to factory defaults.
Lights do not dim or turn ON as expected.
• Ensure that 0 –10 V control lines are wired properly.
• Ensure that fixture does not require an inverted signal (10 – 0 V control).
• Ensure that the wires are connected between the Project 37 Sensor and Project 37 Control Module
• Ensure that fixture does not require an inverted signal (10 – 0 V control).
• Ensure that the wires are connected between the Project 37 Sensor and Project 37 Control Module
Lights do not respond to Wireless Transmitter(s).
• Ensure that the breaker(s) to the PowPak
®
Dimming Module and ballasts are energized.
• Ensure that Wireless Transmitters are associated to the PowPak
®
Dimming Module.
Reset to factory defaults.
Lights are unstable at low-end or flash/flicker at
turn-on or turn-off.
turn-on or turn-off.
• Adjust low-end trim.
Wireless Transmitter(s) cannot be associated to
PowPak
PowPak
®
Dimming Module.
• The maximum number of Wireless Transmitters have been associated to the PowPak
®
Dimming Module. To remove a previously set up Wireless
Transmitter, tap a Wireless Transmitter button three times; on the third tap hold for three seconds and then tap three more times.
FCC Information (FC-0, FC-1 and FC-2 only)
This device complies with part 15 of the FCC Rules and Industry
Canada license-exempt RSS standard(s). Operation is subject
to the following two conditions: (1) This device may not cause
interference, and (2) this device must accept any interference,
including interference that may cause undesired operation.
Modifications not expressly approved by Lutron Electronics Co.,
Inc. could void the user’s authority to operate this equipment.
NOTE: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
• Re-orient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
Set a Favorite Light Level
For Pico
®
Wireless Controls with a
Favorite Button.
A
Adjust lights to desired level:
Use Raise button “ ” or Lower button “ ” on Pico
®
wireless control.
B
Save favorite level:
Press and hold Favorite button for 6 seconds.
The load flashes 3 times to confirm that the set level is saved.
The load flashes 3 times to confirm that the set level is saved.
Technical Assistance | 1.800.523.9466 USA, Canada, and the Caribbean | +44.(0)20.7702.0657 Europe | +1.610.282.3800 Others | www.lutron.com