Lutron Electronics Company Inc 0108 用户手册

041467 

Rev. A

07/2014

Part of the Energi TriPakR Family

Project 37 Load Control Module | 

Programming

Lutron Electronics Co., Inc., 7200 Suter Road

Coopersburg, PA 18036-1299 U.S.A.

Lutron EA Ltd. (“Lutron EA”) warrants each unit to be free from 

defects in material and workmanship and to perform under 

normal use and service. To the extent permitted by law, Lutron 

EA and Lutron Electronics Co. Inc. (“Lutron”) make no warranties 

or representations as to the units except as set forth herein. This 

warranty shall run for a period of two years from the date of purchase 

and Lutron’s obligations under this warranty are limited to remedying 

any defect, replacing any defective part or replacement (at Lutron 

EA’s sole option) and shall be effective only if the defective unit 

is shipped to Lutron EA postage prepaid within 24 months after 

purchase of the unit. Repair or replacement of the unit does not affect 

the expiry date of the warranty. This warranty does not cover damage 

or deficiencies due to abuse, misuse, inadequate wiring or insulation 

or use or installation other than in accordance with instructions 

accompanying the unit. 
To the extent permitted by law, neither Lutron EA nor Lutron shall be 

liable for any other loss or damage including consequential or special 

loss or damages, loss of profits, loss of income, or loss of contracts 

arising out of or relating to the supply of the unit or the use of the unit 

and the purchaser assumes and will hold harmless Lutron EA and 

Lutron in respect of all such loss or damage. Nothing in this warranty 

shall have the effect of limiting or excluding Lutron EA’s or Lutron’s 

liability for fraud or for death or personal injury resulting from its own 

negligence, or any other liability, if and to the extent that the same 

may not be limited or excluded as a matter of law. 
This warranty does not affect the statutory rights of consumer 

purchasers of this product.  
Although every attempt is made to ensure that catalogue information 

is accurate and up-to-date, please check with Lutron EA before 

specifying or purchasing this equipment to confirm availability, exact 

specifications, and suitability for your application.  
For information on other products, please see the Warranty 

enclosed with the product.
Lutron, Pico, PowPak, Energi TriPak, Clear Connect, EcoSystem, 

and ) are registered trademarks and Radio Powr Savr is a 

trademark of Lutron Electronics Co., Inc. 
©2014 Lutron Electronics Co., Inc.

Reset Factory Defaults

Note: In some instances, it may be necessary 
to reset the PowPak

®

 Dimming Module and 

connected devices back to factory default 
settings. Before beginning, make sure that all 
devices are connected and powered.

 

 Triple-tap any button on the PowPak

®

 Dimming 

Module and hold until the LED begins to flash 
slowly; release button.

 

 Within 3 seconds of the start of flashing, triple-tap 

the same button again and the LEDs will flash 
rapidly indicating that the unit has been reset to 
factory defaults.
Note: Any associations or programming 
previously set up with the PowPak

®

 will be erased 

and will need to be re-programmed.

Set Low-End and High-End Trim

For best results, minimize the amount of sunlight entering the room before performing the following procedures.
Low-End Trim

 

A  Enter low-end trim adjustment mode:

Press and hold Lower button “ ” for 12 seconds.
Lights will flash high-low-high and LED will begin flashing.

 

B  Adjust the low-end trim:

Use Raise button “ ” and Lower button “ ” to adjust and set the lights to the desired low-end (1 to 45%).

 

C  Save the low-end trim:

Press and hold Toggle button “  ” for 6 seconds to save setting.
LED will begin flashing and then turn solid to indicate new level has been saved.
High-End Trim

 

D  Enter high-end trim adjustment mode:

Press and hold Raise button “ ” for 12 seconds.
Lights will flash high-low-high and LED will flash.

 

E  Adjust the high-end trim:

Use Raise button “ ” and Lower button “ ” to adjust and set the lights to the desired high-end 
(55 to 100%).

 

F  Save the high-end trim:

Press and hold Toggle button “  ” for 6 seconds to save setting.
LED will begin flashing and then turn solid to indicate new level has been  

Notes
Depending on the fixture 

manufacturer or load, low-end 

and high-end trim may need to 

be adjusted.

• Trim low-end to ensure a stable 

light level because some loads 

will flicker or drop out if trimmed 

too low.

• Be sure that you can turn on the 

lights to the low-end trim level 

without any abnormal operation.

• The factory default high-end trim 

will normally be sufficient for most 

applications. Trim as desired.

Raise

Lower

Favorite

Troubleshooting                                                                                                                                             

www.lutron.com

Ballasts cannot be controlled locally from 
PowPak

®

 Dimming Module.

•  Ensure that the breaker(s) to the PowPak

®

 Dimming Module are energized.

•  Ensure that the PowPak

®

 Dimming Module switched hot lead is wired to the ballast(s).

•  Ensure that the PowPak

®

 Dimming Module 0 –10 V control lines are wired to the ballast(s).

  Reset to factory defaults.

Lights do not dim or turn ON as expected.

•  Ensure that 0 –10 V control lines are wired properly.
•  Ensure that fixture does not require an inverted signal (10 – 0 V control).
•  Ensure that the wires are connected between the Project 37 Sensor and Project 37 Control Module

Lights do not respond to Wireless Transmitter(s).

•  Ensure that the breaker(s) to the PowPak

®

 Dimming Module and ballasts are energized.

•  Ensure that Wireless Transmitters are associated to the PowPak

®

 Dimming Module.

  Reset to factory defaults.

Lights are unstable at low-end or flash/flicker at 
turn-on or turn-off.

•  Adjust low-end trim.

Wireless Transmitter(s) cannot be associated to 
PowPak

®

 Dimming Module.

•  The maximum number of Wireless Transmitters have been associated to the PowPak

®

 Dimming Module. To remove a previously set up Wireless 

Transmitter, tap a Wireless Transmitter button three times; on the third tap hold for three seconds and then tap three more times.

FCC Information (FC-0, FC-1 and FC-2 only)

This device complies with part 15 of the FCC Rules and Industry 

Canada license-exempt RSS standard(s). Operation is subject 

to the following two conditions: (1) This device may not cause 

interference, and (2) this device must accept any interference, 

including interference that may cause undesired operation. 

Modifications not expressly approved by Lutron Electronics Co., 

Inc. could void the user’s authority to operate this equipment.

NOTE: This equipment has been tested and found to comply 

with the limits for a Class B digital device, pursuant to part 

15 of the FCC Rules. These limits are designed to provide 

reasonable protection against harmful interference in a residential 

installation. This equipment generates, uses and can radiate radio 

frequency energy and, if not installed and used in accordance 

with the instructions, may cause harmful interference to radio 

communications. However, there is no guarantee that interference 

will not occur in a particular installation. If this equipment does 

cause harmful interference to radio or television reception, which 

can be determined by turning the equipment off and on, the user is 

encouraged to try to correct the interference by one or more of the 

following measures:

• Re-orient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from 

that to which the receiver is connected.

Set a Favorite Light Level

For Pico

®

 Wireless Controls with a 

Favorite Button.

 

  Adjust lights to desired level:

Use Raise button “ ” or Lower button “ ” on Pico

®

 wireless control.

 

  Save favorite level:

Press and hold Favorite button for 6 seconds.
The load flashes 3 times to confirm that the set level is saved.

Technical Assistance  |  1.800.523.9466  USA, Canada, and the Caribbean  |  +44.(0)20.7702.0657 Europe  |  +1.610.282.3800 Others  |  www.lutron.com