CALAMP WIRELESS NETWORKS INC. BDD4T881 Manual De Usuario
120 20170-200
Paragon
PD
Technical Manual
18
To run the program, you will need:
-
A PC or portable computer with a 486 class
CPU or better.
CPU or better.
-
2 free megabytes of RAM.
-
A hard disk.
-
An available COM port.
-
A serial mouse, with its own driver installed
is strongly recommend however most actions
can also be done using keyboard commands.
is strongly recommend however most actions
can also be done using keyboard commands.
Paragon
PD
and Paragon products share the RIS
program with the MobilPac family of products. It
is available on diskette, Dataradio p/n 085
03355-00n. Please refer to the readme.txt file
included on the diskette for installation
instructions.
is available on diskette, Dataradio p/n 085
03355-00n. Please refer to the readme.txt file
included on the diskette for installation
instructions.
4.1 Operation
This support program is DOS-based and can be
run in MS-Windows © MS-DOS mode.
run in MS-Windows © MS-DOS mode.
DO NOT have more than one copy of this pro-
gram loaded at any given time in separate win-
dows. Doing so creates COM port sharing con-
flicts and program failure.
gram loaded at any given time in separate win-
dows. Doing so creates COM port sharing con-
flicts and program failure.
It has the general look and feel of an MS-
Windows program. Mouse operation is the con-
ventional click, double-click plus click and drag
Windows program. Mouse operation is the con-
ventional click, double-click plus click and drag
method. Only left mouse button operation is
supported.
supported.
Any command or selection shown in gray is ei-
ther unavailable or is awaiting another action
before activating.
ther unavailable or is awaiting another action
before activating.
Help in the program is available at all points by
pressing the F1 key. If a subject is highlighted,
the help displayed will be context sensitive. Oth-
erwise, the Index List is displayed.
pressing the F1 key. If a subject is highlighted,
the help displayed will be context sensitive. Oth-
erwise, the Index List is displayed.
4.2 To connect and start RIS
1- Connect a suitable 9-pin straight PC cable,
between the BDLC
PD
rear-mounted DEV2
port (see Figure 4), defined as DMP/setup
port (19200 bauds) at the time of manufac-
ture, and the port of the PC (or portable
computer) that will be running the RIS pro-
gram. If needed, a 9/25 pin-adapter and a 25-
pin PC cable may be used.
port (19200 bauds) at the time of manufac-
ture, and the port of the PC (or portable
computer) that will be running the RIS pro-
gram. If needed, a 9/25 pin-adapter and a 25-
pin PC cable may be used.
2- Check that Paragon
PD
is ON.
3- To run the Radio Service Software (RIS):
Note:
Refer to the RIS Readme.txt file for
more details on how to set the Win-
dows environment, connect, install
and run this program.
more details on how to set the Win-
dows environment, connect, install
and run this program.
•
In DOS, change to the directory where
the program is installed and type
mpac_ris.exe and press ENTER.
mpac_ris.exe and press ENTER.
•
In WIN 3.x, click on File, then on Run,
type the path or browse to select, click
on OK to run mpac_ris.exe.
on OK to run mpac_ris.exe.
•
In WIN 9x, click on Start, then on Run,
type the path or browse to select, click
on OK to run mpac_ris.exe.
on OK to run mpac_ris.exe.