Badger Meter Inc HREBT Manual De Usuario

Crimp the Gel-Connector using the Crimping Tool making sure the

plunger is fully seated so there is no visual gap between the cap’on

the plunger and the shell of the Gel-Connector.

Gel connector in the crimping tool

Proper crimp—plunger fully seated

Inspect the Gel-Connector to insure that the conductors did not

back out during crimping and that the Gel-Connector plunger is

fully seated.

Plunger is fully seated

Conductor is all the way through

Conductors are still all the way through to the end of the

Gel-Connector and the plunger is fully seated.

Repeat this procedure for the remaining like color conductors.

If the wire is cut or broken and requires a field splice after initial

installation, connect like colors to maintain proper installation.

PIT INSTALLATIONS

Insert the entire splice assembly into the filled splice tube

P/N 62085-001 as indicated in the figure below. Close the cover

with leads exiting alternate sides as indicated in Figure 2.

Figure 2: Splice enclosure assembly

HRE WITH TERMINAL SCREWS

OTEE:

The HRE with optional terminal screws is suitable for indoor

installation only.

The terminal screws are identified by the letters “R”, “B”, and “G”

(standing for Red, Black, and Green) molded into the screw cavity.

Strip approximately 1-1/2" of outer insulation sheath using the

59989-001 coax stripping tool. Use caution in removing the outer

sheath so that the inner wire insulation is not damaged.

Unwind the outer foil shield from the cable and cut it off even with

the outer sheath using the wire cutting pliers. Cut the uninsulated

shield drain wire even with the outer sheath.

Strip approximately 1/2" of insulation from the inner wires using the

59993-001 wire stripper. Use a screwdriver to loosen the terminal

screws sufficiently to allow the bare wire ends to fit below the screw

heads. Bend the bare wire ends into hook shapes that will closely fit

around the shafts of the terminal screws, and hold the hooks around

the screw shafts while tightening the screws with the screwdriver.

Do not overtighten screws. The hooks should be oriented with the

openings to the right, so that tightening the screws (by turning to

the right) will tend to draw the wire closer to the screw.
Place plastic cable tie P/N 34776-001 approximately 1/4" from end

of outer insulation sheath. Tighten securely for strain relief. Remove

excess cable tie. Ensure that the cable exits the terminal screw cavity

via the opening on the right side of the cavity wall and that cable

tie resides on interior of terminal cover. Place the cover over the

terminal screw cavity and secure by tightening the Torx screw.

TESTING

After connections are complete, test the entire installation including

the HRE, wiring, and remote or pit module for proper operation in

accordance with the instructions supplied with the module.

Install the HRE on the water meter and secure it using the Torx

screw provided.

LICENSE REQUIREMENTS

This device complies with Part 15 of the FCC Rules. Operation of

this device is subject to the following two conditions: (1) This device

may not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause

undesired operation. Any changes made by the user not approved

by Badger Meter can void the user’s authority to operate the

equipment. No license is required by the utility to operate an HRE

meter reading system.

www.badgermeter.com

ADE, BadgerTouch, Recordall, and RTR are registered trademarks of Badger Meter, inc. Other trademarks appearing in this document are the property of their respective entities.
Due to continuous research, product improvements and enhancements, Badger Meter reserves the right to change product or system specifications without notice, except to the
extent an outstanding contractual obligation exists. © 2013 Badger Meter, Inc. All rights reserved.

Czech Republic | Badger Meter Czech Republic s.r.o. | Maříkova 2082/26 | 621 00 Brno, Czech Republic | +420-5-41420411

Slovakia | Badger Meter Slovakia s.r.o. | Racianska 109/B | 831 02 Bratislava, Slovakia | +421-2-44 63 83 01

This device complies with Industry Canada licence-exempt RSS standard(s).

Operation is subject to the following two conditions: (1) this device may

not cause interference, and (2) this device must accept any interference,

including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables

aux appareils radio exempts de licence. L'exploitation est autorisée aux

deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage,

et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique

subi, même si le brouillage est susceptible d'en compromettre le

fonctionnement.