Digital Monitoring Products Inc PC0192 Manual De Usuario

REPLACE THE BATTERY

1.  Remove the cover by pushing the button on the end of the cover and gently pulling upwards.
2.  Remove the old battery and dispose of it properly.
3.  Observing polarity, place the new battery in the holder and press into place.
4.  Snap the transmitter housing cover back on the base.

Caution: Properly dispose of used batteries. Do not recharge, disassemble, heat above 212°F (100°C), or incinerate. Risk of fire,
explosion, and burns.

Sensor Reset to Clear LOBAT

When the battery needs to be replaced, a

LOBAT message will display on the keypad. Once the battery is replaced, a sensor reset is

required at the system keypad to clear the

LOBAT message.

1.  On a Thinline keypad, press and hold “2” for two seconds. On a touchscreen keypad press RESET.
2.  Enter your user code if required.
3.  The keypad displays

SENSORS OFF followed by SENSORS ON.

FCC INFORMATION

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

The antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm (7.874 in.) from all persons. It

must not be located or operated in conjunction with any other antenna or transmitter.
Changes or modifications made by the user and not expressly approved by the party responsible for compliance could void the user’s

authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Industry Canada Information

This device complies with Industry Canada Licence‑exempt RSS standard(s). Operation is subject to the following two conditions:

1. this device may not cause interference, and
2. this device must accept any interference, including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est

autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter

tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
This system has been evaluated for RF Exposure per RSS‑102 and is in compliance with the limits specified by Health Canada Safety

Code 6. The system must be installed at a minimum separation distance from the antenna to a general bystander of 7.87 inches (20 cm)

to maintain compliance with the General Population limits.
L’exposition aux radiofréquences de ce système a été évaluée selon la norme RSS-102 et est jugée conforme aux limites établies par le

Code de sécurité 6 de Santé Canada. Le système doit être installé à une distance minimale de 7.87 pouces (20 cm) séparant l’antenne

d’une personne présente en conformité avec les limites permises d’exposition du grand public.

Designed, engineered,

and manufactured in

Springfield, Missouri

I N T R U S I O N • F I R E • A C C E S S • N E T W O R K S

2500 North Partnership Boulevard

Springfield, Missouri 65803‑8877

800-641-4282 | dmp.com

Certifications

FCC Part 15 Registration ID CCKPC0192 (pending)

Industry Canada Registration ID 5251A‑PC0192 (pending)

Compatibility

1100X Wireless Receiver version 104 or higher

1100XH Wireless Receiver version 105 or higher

1100D Wireless Receiver version 104 or higher

1100DI Wireless Receiver Version 105 or higher

1100DH Wireless Receiver Version 105 or higher

XT50 Series panels with integrated wireless receiver version 101 or higher

XTL Series panels with integrated wireless receiver version 104 or higher

XTLplus Series Panels

Patents

U. S. Patent No. 7,239,236

Specifications

Battery

Life Expectancy

3 Years (normal operation)

Type

3.0V Lithium CR123A

Frequency Range

905‑924 MHz

Dimensions

3.3” L x 1.6” W x 1.2” H

Color White

Housing Material

Flame retardant ABS

Accessories

470PB

Water Sensor Probe

T280R

Temperature Sensor Probe

Replacements

CR123A

3.0V Lithium Battery

PRELIMINA