Lectrosonics Inc HHAB1 Manual De Usuario
HHa
LECTROSONICS, INC.
10
Input Gain Adjustment
The two bicolor Modulation LEDs (located at the bot-
tom of the control panel) provide a visual indication of
the audio signal level entering the transmitter.
tom of the control panel) provide a visual indication of
the audio signal level entering the transmitter.
5
623.400
-40
-20
0
A
The audio level is shown by
LEDs and in the LCD screen.
The gain should be set so that
the -20 LED just turns red on
the loudest peak (the onset of
limiting).
The LEDs will glow either red or green to indicate
modulation levels as shown in the following table.
modulation levels as shown in the following table.
Signal Level
-20 LED
-10 LED
Less than -20 dB
Off
Off
-20 dB to -10 dB
Green
Off
-10 dB to +0 dB
Green
Green
+0 dB to +10 dB
Red
Green
Greater than +10 dB
Red
Red
It is best to go through the following procedure with the
transmitter in the “standby” mode so that no audio will
enter the sound system, which could cause feedback.
transmitter in the “standby” mode so that no audio will
enter the sound system, which could cause feedback.
1) With fresh batteries in the transmitter, power the
unit on into “standby” (no transmission) mode.
2) Press the MENU/SEL button once to enter the
setup menu. Use the UP/DOWN buttons to select
Gain. Press the MENU/SEL button again to enter
the setup screen.
Gain. Press the MENU/SEL button again to enter
the setup screen.
3) Hold the microphone the way it will be used in
actual operation.
4) Speak or sing at the same voice level that will
actually be used during the program, while ob-
serving the modulation LEDs. Use the UP/DOWN
buttons to adjust the gain until the –20 dB LED
starts to flicker red and the –10 dB glows green.
serving the modulation LEDs. Use the UP/DOWN
buttons to adjust the gain until the –20 dB LED
starts to flicker red and the –10 dB glows green.
5) Once the audio gain has been set, the signal can
be sent through the sound system for overall level
adjustments, monitor settings, etc. To do this, the
unit must be set to transmit (see Powering On
and Off, and the Standby Mode on page 7).
adjustments, monitor settings, etc. To do this, the
unit must be set to transmit (see Powering On
and Off, and the Standby Mode on page 7).
NOTE: Full modulation is achieved when the
-20 LED first turns red. 30 dB of clean limiting is
available above this point.
-20 LED first turns red. 30 dB of clean limiting is
available above this point.
Phase
The phase (polarity) of the audio can be inverted to
match other microphone capsules as needed.
match other microphone capsules as needed.
TxPower
Phase
Backlgt
Rf On?
Rf On?
Phase
Pos
Neg
Neg
Backlgt
The LCD includes a backlight that illuminates the
display for easier viewing in dim lighting conditions. It
is set to come on when any button on the control panel
is pressed, then stay on for either 30 seconds or 5
minutes, or to stay on all the time.
display for easier viewing in dim lighting conditions. It
is set to come on when any button on the control panel
is pressed, then stay on for either 30 seconds or 5
minutes, or to stay on all the time.
Compat
Tuning
TxPower
Tuning
TxPower
Backlgt
Backlgt
On
30 sec
5 min
30 sec
5 min
Rf On?
The transmitter output can be switched on or off with
this menu item. This is useful, for example, when the
transmitter is in the “standby” mode during setup, al-
lowing it to be turned on for normal operation without
having to cycle the power.
this menu item. This is useful, for example, when the
transmitter is in the “standby” mode during setup, al-
lowing it to be turned on for normal operation without
having to cycle the power.
Tuning
TxPower
Backlgt
TxPower
Backlgt
Rf On?
Rf On?
No
Yes
Yes
This menu item can also be used to change the trans-
mitter to the “standby” mode with the RF output turned
off for additional setup.
mitter to the “standby” mode with the RF output turned
off for additional setup.
Default
The default setting simple returns the transmitter back
to the factory settings and any of the menu items can
be readjusted from that default point.
to the factory settings and any of the menu items can
be readjusted from that default point.
Default
s e t t i n g s
s e t t i n g s
No
Yes
Yes
TxPower
Backlgt
Rf On?
Backlgt
Rf On?
Default