CalAmp 3640HEB Manual De Usuario
9/27/2017
LMU-3640 Hardware & Installation Guide - PULS Wiki
https://puls.calamp.com/wiki/LMU-3640_Hardware_%26_Installation_Guide
11/23
Status
Color
GPS
Green
Comm
Orange
WiFi/BT
Blue
4 Configuration and Activation
This section details how to quickly get an LMU-3640™ provisioned and configured to point at a specific server. It is assumed that a PEG script has
already been created and is being managed through LMU Manager or PULS™, the CalAmp Maintenance System.
already been created and is being managed through LMU Manager or PULS™, the CalAmp Maintenance System.
We are making three assumptions to simplify the setup process:
You have created, installed and configured an LM Direct™ Server to receive messages from the LMU-3640™. (See LM Direct™
Reference Guide for details)
You are using the standard wiring harness from CalAmp and the serial port expansion harness.
You have created a HyperTerminal or Putty session.
You have contacted the CalAmp sales team regarding the network availability of the LMU-3640™. This device may not be supported
for all the carriers or networks listed in this section (CDMA-Verizon, CDMA-Sprint, HSPA, GSM), for product availability consult the
CalAmp sales team.
Reference Guide for details)
You are using the standard wiring harness from CalAmp and the serial port expansion harness.
You have created a HyperTerminal or Putty session.
You have contacted the CalAmp sales team regarding the network availability of the LMU-3640™. This device may not be supported
for all the carriers or networks listed in this section (CDMA-Verizon, CDMA-Sprint, HSPA, GSM), for product availability consult the
CalAmp sales team.
4.1 Quick Start - General Config
All LMU-3640™s must go through a common step during the configuration and provisioning process. Specifically, this is pointing the LMU to
your LM Direct™ server, either via IP or a URL.
your LM Direct™ server, either via IP or a URL.
This configuration process is accomplished via a series of AT Commands:
1. Power up the LMU-3640™ and connect a serial cable from the LMU to your laptop
2. Open a terminal session to the LMU-3640™
3. Enter the address of the LM Direct™ server:
2. Open a terminal session to the LMU-3640™
3. Enter the address of the LM Direct™ server:
AT$APP PARAM 2319,0,ddd.ddd.ddd.ddd
AT$APP PARAM 768,0,ddd.ddd.ddd.ddd (32-bit products only)
AT$APP PARAM 769,0,ppppp
AT$APP PARAM 768,0,ddd.ddd.ddd.ddd (32-bit products only)
AT$APP PARAM 769,0,ppppp
Where ddd.ddd.ddd.ddd is the publicly addressable IPV4 address of your LM Direct™ server and ppppp is the UDP port number.
4. Alternatively if a URL has been set up for your LM Direct™ server, the LMU may be programmed with:
AT$APP PARAM 2319,0,myURL.MyCompany.Com
Where myURL.MyCompany.com is the URL assigned to the server.
5. Enter ATIC to verify the correct settings are displayed for your Inbound Server.
This configuration process is accomplished via a series of SMS Commands:
1. Power up the LMU-3640™ and your handset
2. From the handset, send an SMS message to the LMU-3640™ phone number:
2. From the handset, send an SMS message to the LMU-3640™ phone number:
!RP,2319,0,ddd.ddd.ddd.ddd
!RP,768,0,ddd.ddd.ddd.ddd (32-bit products only)
!RP,769,0,ppppp
!RP,768,0,ddd.ddd.ddd.ddd (32-bit products only)
!RP,769,0,ppppp
Where ddd.ddd.ddd.ddd is the publicly addressable IPV4 address of your LM Direct™ server and ppppp is the UDP port number
3. Alternatively if a URL has been set up for your LM Direct™ server, the LMU may be programmed with:
!RP,2319,0,myURL.MyCompany.Com