BW Broadcast Ltd TX300V2 Manual De Usuario
TX V2 FM Broadcast Transmitter
Menu Map
24
DHCP DNS 1 Reads back the DHCP Primary DNS server. Accepts IPv4 address in
the form 123.456.789.123.
the form 123.456.789.123.
DHCP DNS 2 Reads back the DHCP Secondary DNS server. Accepts IPv4 address
in the form 123.456.789.123.
in the form 123.456.789.123.
Static IP Sets the manual IP address. Accepts IPv4 address in the form
123.456.789.123.
123.456.789.123.
Static SM Sets the manual subnet mask. Accepts IPv4 address in the form
123.456.789.123.
123.456.789.123.
Static GW Sets the manual gateway. Accepts IPv4 address in the form
123.456.789.123.
123.456.789.123.
Static DNS 1 Sets the manual Primary DNS server. Accepts IPv4 address in the form
123.456.789.123.
123.456.789.123.
Static DNS 2 Sets the manual secondary DNS server. Accepts IPv4 address in the
form 123.456.789.123.
form 123.456.789.123.
MAC Reads back the Ethernet MAC address.
o
E-Mail
Test
•
Test Sends a test e-mail.
•
Recipient(s) Sets who the test email will be sent to. Multiple addresses must
be separated by commas. Accepts text of up to 99 characters.
be separated by commas. Accepts text of up to 99 characters.
Send via Sets the method used for sending emails. For simplicity, choose BW
Broadcast.
Broadcast.
From Sets the email address of the sender. The unit will send e-mails through this
address. Accepts text of up to 64 characters.
address. Accepts text of up to 64 characters.
Recipient(s) Sets the recipients of the emails. Multiple addresses must be separated
by commas. Accepts text of up to 99 characters.
by commas. Accepts text of up to 99 characters.
Host Sets the IP address of the SMTP server. Accepts text of up to 64 characters.
Port Sets the port number of the SMTP server. This parameter accepts values from 1
to 1024.
to 1024.
Username Sets the username for SMTP authentication. Must be left blank if no
authentication is required. Accepts text of up t64 characters.
authentication is required. Accepts text of up t64 characters.
Password Sets the password for SMTP authentication. Must be left blank if no
authentication is required. Accepts text of up to 64 characters.
authentication is required. Accepts text of up to 64 characters.
Max emails a day Sets the maximum number of emails allowed to be sent by the unit
in a single day. This parameter accepts values from 1 to 1000.
in a single day. This parameter accepts values from 1 to 1000.
Emails sent today Reports the number of emails sent today. This parameter accepts
values from 0 to 100000.
values from 0 to 100000.
o
HTTP
Enable Enables/disables the web server.
Port Sets the webserver TCP port. Disable HTTP to change. This parameter accepts
values from 1 to 1024.
values from 1 to 1024.
o
Telnet
Enable Enables/disables the telnet server.
Port Sets the telnet TCP port. Disable Telnet to change. This parameter accepts
values from 1 to 1024.
values from 1 to 1024.
o
RS232
Enable Enables/disables the RS232 remote.
Baud rate Sets the RS232 baud rate.
o
Log
RS232 Enables/disables logging to RS232.
File Enables/disables logging to file.
UDP
•
Enable Enables/disables logging messages to a remote UDP logging/syslog
server.
server.
•
IP Sets the IP address where the log messages should be sent via UDP.
Accepts IPv4 address in the form 123.456.789.123.
Accepts IPv4 address in the form 123.456.789.123.
•
Port Sets the port where the log messages should be sent via UDP. Disable
UDP to change. This parameter accepts values from 1 to 10000.
UDP to change. This parameter accepts values from 1 to 10000.
o
About
Serial Number Reads back serial number.
Product Version Reads back the product version.
Hardware Version Reads back the hardware version.
Software Version Reads back the software version.
Control Version Reads back the control board version.
AIO FW Version Reads back the AIO board firmware version.
o
Reboot Reboots the unit.
o
Factory Reset Performs a factory reset. All user presets will be lost.