Red Bear Company Limited PHAT-IOT Manual De Usuario
WiFi Interface : SDIO v2.0
Bluetooth Interface : UART / PCM
Operating voltage : 3.3V
Operating temperature : -30˚C to 85˚C
Storage temperature : -40˚C to 85˚C
Humidity : Operating Humidity 10% to 95% Non-Condensing
Bluetooth Interface : UART / PCM
Operating voltage : 3.3V
Operating temperature : -30˚C to 85˚C
Storage temperature : -40˚C to 85˚C
Humidity : Operating Humidity 10% to 95% Non-Condensing
Limitations
FM is not supported with the board.
Although the board supports Bluetooth keyboard, you still need to use a wired keyboard to set up for it.
Although the board supports Bluetooth keyboard, you still need to use a wired keyboard to set up for it.
FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the
equipment.
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the
equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —
Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —
Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help.
The modular can be installed or integrated in mobile or fix devices only. This modular cannot be installed in any portable device, for example,
USB dongle like transmitters is forbidden. FCC Radiation Exposure Statement This modular complies with FCC RF radiation exposure limits
set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter. This modular must be installed and operated with a minimum distance of 20 cm between the radiator and user body.
If the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the
module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following:
"Contains Transmitter Module FCC ID: 2ABXJ-PHAT-IOT Or Contains FCC ID: 2ABXJ-PHAT-IOT" When the module is installed inside another
device, the user manual of the host must contain below warning statements; 1. This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference
received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the equipment. The devices must be installed and used in strict
accordance with the manufacturer's instructions as described in the user documentation that comes with the product. Any company of the
host device which install this modular with limit modular approval should perform the test of radiated emission and spurious emission
according to FCC part 15C : 15.247 and 15.209 requirement, Only if the test result comply with FCC part 15C : 15.247 and 15.209
requirement，then the host can be sold legally.
USB dongle like transmitters is forbidden. FCC Radiation Exposure Statement This modular complies with FCC RF radiation exposure limits
set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter. This modular must be installed and operated with a minimum distance of 20 cm between the radiator and user body.
If the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the
module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following:
"Contains Transmitter Module FCC ID: 2ABXJ-PHAT-IOT Or Contains FCC ID: 2ABXJ-PHAT-IOT" When the module is installed inside another
device, the user manual of the host must contain below warning statements; 1. This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference
received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the equipment. The devices must be installed and used in strict
accordance with the manufacturer's instructions as described in the user documentation that comes with the product. Any company of the
host device which install this modular with limit modular approval should perform the test of radiated emission and spurious emission
according to FCC part 15C : 15.247 and 15.209 requirement, Only if the test result comply with FCC part 15C : 15.247 and 15.209
requirement，then the host can be sold legally.