Brighton Technologies Pty Ltd BMTX-500 Manual De Usuario
Page | 8
Putting the BTG Customer Pagers to Sleep
If your BTG Pagers serve an area that is not used very often, such as conference rooms, or reception
halls, you may find it beneficial to put the pagers to sleep. Putting the pagers to sleep simply means
setting the pagers to turn off. When pagers are asleep, they do not tone when they are paged, and they
also do not tone if the batteries are low if they are disconnected from the Charging Rack. This may also
prove helpful if you move your BTG Pager System from site to site as a catering company may.
halls, you may find it beneficial to put the pagers to sleep. Putting the pagers to sleep simply means
setting the pagers to turn off. When pagers are asleep, they do not tone when they are paged, and they
also do not tone if the batteries are low if they are disconnected from the Charging Rack. This may also
prove helpful if you move your BTG Pager System from site to site as a catering company may.
This command is sent from your BTG transmitter. It is also highly recommended to make sure that all of
the pagers are collected in from your floor before changing this feature, as not to alert customers that
may be waiting to be called.
the pagers are collected in from your floor before changing this feature, as not to alert customers that
may be waiting to be called.
To perform this procedure, all charging racks must be unplugged at the wall. When you unplug your
charging racks, you may notice that all of the pagers in that rack vibrate 2 times and flash their LED’s.
This is normal behaviour and can be ignored. After this procedure is complete, all of your pages will
essentially turn off. No LED’s will display, and with BTG Voice Pagers, the LCD Number display will also
go out. To wake pagers, simply re‐plug the racks into the wall.
charging racks, you may notice that all of the pagers in that rack vibrate 2 times and flash their LED’s.
This is normal behaviour and can be ignored. After this procedure is complete, all of your pages will
essentially turn off. No LED’s will display, and with BTG Voice Pagers, the LCD Number display will also
go out. To wake pagers, simply re‐plug the racks into the wall.
After all of the charging racks in your system are unplugged, return to the transmitter and follow the
following procedure:
following procedure:
1. At the standard idle screen, enter 9998 into the To: area on your transmitter.
2. Press the orange enter key
3. The transmitter will now wait for you to input a message. Enter #*016. The * and the # will show
on the LCD screen as ] and [. This is normal
4. Press the green send button to transmit the sleep command to the pagers..
Shortly after sending the command, all of your BTG Pagers will go to sleep. To wake them back up again,
simply plug the charging racks back into the wall. They will then power on and will be ready to be paged
again.
simply plug the charging racks back into the wall. They will then power on and will be ready to be paged
again.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
1) this device may not cause harmful interference, and 2) this device must accept any interference
received, including interference that may cause undesired operation.
1) this device may not cause harmful interference, and 2) this device must accept any interference
received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur