Schlegel S_789-602 4-channel Radio Receiver With 4 Changeover Contacts 4-channel-radio receiver S_789-602 Manual De Usuario

Los códigos de productos
S_789-602
Descargar
Página de 4
Mounting - and Installation Instructions 789-601 / 789-602 incl. Versions /xxx- xxx
WAGO Kontakttechnik GmbH & Co. KG, D-32423 Minden, Hansastraße 27  •www.wago.com
9970-0966/0789-0601/08-07_SW03
alternative:
ð further flashing of Channel LED
ð wait appr.  5 seconds 
ð Operate transmitter / switch again 
ð Channel LED for 4 seconds ON
ð Receiver leaves LRN-Mode;  LED „LRN“OFF
5.9 Deleting Assignment of all Transmitters / CLR-Button
By pressing the CLR-Button ALL previously assigned 
transmitters are deleted.
ð Press CLR Button
ð LED  „LRN“flashes (0.5 Hz); no transmitters 
assigned
6. Changing Mode of Operation (from software 02)
In state of delivery, the “Switching-Mode”is active. For changing of 
the behaviour, the LRN button must be pressed for ~2s during 
Power-Up. All 5s the following mode of operation is selected 
(indicated by LED K1...4). To activate the selected function the
LRN Button must be pressed within 5s (signalised with 8Hz 
flashing light of selected function LED. To activate selected 
Function, press LRN-Button again, receiver activates selected 
function and switches to Receive-Mode.
Signalisation of Operating-Mode (LED flashes):
K1= Switching-Mode; K2= Toggle-Mode; K3= Inverted Output 
behaviour; K4=State of output at Power ON
K4+K1=Switching-Mode 2-channel PTM230 (from software 03);  
K4+K2= Toggle-Mode 2-channel PTM230 ( from software 03)
State of delivery of versions 789-60x/001-000 is Toggle-Mode.
7. Transmission Behavior
Commands from transmitters will take about 40 to 70ms for 
transmission, which is based on the EnOcean Radio Technology 
on the 868Mhz band. With the further processing in the Wago 
receiver the delay between operation and execution of the 
command will be up to 100ms.
8. Terminal Assignments
8. 1 Input / Voltage-Supply
FE should be grounded with wiring as short as possible.
8.2 Output / NO Contacts 789-601
8.3 Output / CO Contacts 789-602
5.5 Please observe the following Advices before
activating the Learn-Mode!
The sensitivity of the receiver is reduced to appr. 
5 m as long as Learn-Mode is active.
In Learn-Mode the relay outputs are triggered cyclically 
in parallel to the indication of the status LEDs. If this behavior is 
not allowed in the application, the loads must be disconnected 
be means of the output terminals to assure no risk for health. 
When activating the Learn-Mode the former state of outputs is  
stored and will be activated again when leaving the Learn-
Mode.
5.6 Teaching of Transmitters / Learn (LRN) Button
Operating-state: 
ð Receive-Mode; LED Us ON
or additionally
ð LED „LRN“flashes; no transmitter assigned
1. Switch receiver into LRN-Mode
ð Press LRN at the receiver
ð LRN active - LED  „LRN“ON
ð 1. Channel-LED flashes
2. Select channel for teaching
ð Press LRN at the receiver
ð Next / selected channel LED flashes
3. Operate Radio Transmitter / Switch (submit telegram)
ð Channel LED for 4 seconds ON
ð Selected channel LED flashes again;
further transmitters could be teached on this channel
ð Receiver leaves LRN-Mode
LED „LRN“OFF
alternative:
ð further flashing of Channel LED
ð wait appr.  5 seconds 
ð Operate transmitter / switch again 
ð Channel LED for 4 seconds ON
ð Receiver leaves LRN-Mode;  LED „LRN“OFF
5.7 Exit LRN-Mode
1. Automatically after learning or deleting of transmitters
ð Receiver switches off LRN-Mode 
LED „LRN“ OFF 
• Learn-Mode is deactivated after 30 s automatically; no       
operation required.
ð Receiver switches off LRN-Mode 
LED „LRN“ OFF 
• Leaving via LRN-Button
ð multiple operation of LRN-button
ð Receiver leaves LRN-Mode (after channel 4) 
LED „LRN“ OFF
5.8 Selective Deleting of single Transmitter / LRN Button
Please observe, the transmission range is reduced to appr. 
5 mtrs, even if transmitters should be deleted!
1. Switch Receiver into LRN-Mode
ð Press LRN-Button
ð LRN-Mode active - LED  „LRN“ON
ð LED of 1. Channel flashes
2. Select channel to be „unlearned“
ð Press LRN-Button again
ð LED of next channel flashes
3. Operate button / switch on transmitter (submit telegramm)
ð LED of sel. Channel is 4s OFF
ð Receiver leaves LRN-Mode
LED „LRN“OFF
Pin no.
Determination
11, 12, 14
CO Contacts Ch. 1
21, 22, 24
CO Contacts Ch. 2
31, 32, 34
CO Contacts Ch. 3
41, 42, 44
CO Contacts Ch. 4
Pin
Determ ination
+
Plus (24V)
-
Gnd
FE
functional earth
Pin no.
Determination
13, 14
NO Contact Ch. 1
23, 24
NO Contact Ch. 2
33, 34
NO Contact Ch. 3
43, 44
NO Contact Ch. 4
Page 2