Siemens TRAFFIC CONTROLS TC12 Manual De Usuario
TC12 Installation, Commissioning & Maintenance Handbook
- Connect the cab
s th
(Switch S3)
e Thresh
(Switch S3)
ire Line
nnection
(Switch S4)
(Switch S6)
n Comm
cations M
od (Jumpers)
ate / Mo
(GMM
ion Addr
(GAD)
r of Outs
ions on th
ine (GNO
r of Cont
Bytes for
Outstatio
on the lin
(GCW)
Number of Reply Bytes for all Outstations on the line (GRW)
puts and Repl Bytes
and Data Di
lays
ation
al Propagation
elay
(GPD)
) to (4) are configure
es on the Outstation P
as desc
d
n 3.2.2.3. These swi
telephone line commu
ations vi
modems.
nfigured using the jumpers on the daughter board fitted to OTUs that
communications with the Instation – see section 3.2.2.4.
for
k and the positions of the OTU PCB, power
supply and detector cards are shown.
ote 1:The 11" version of the rack will accept a maximum of four single
The 19" versi
ccept up to 12 single
te.
e mounted Pelican
3.2.2 Configuring the Outstation PCB
he two variants of Outstation PCB.
ates using a modem communications
CB that is capable of operating with a
ling
- Configure the Outstation using the Handset terminal
The item
The item
at need configuring include:
Output Power Level
Receiv
old
2 or 4 W
Co
600
Ω / High Impedance Line Termination
Instatio
uni
eth
Baud R
de
)
Outstat
Numbe
Numbe
ess
tat
e L
)
Numbe
rol
all
ns
e
Digital In
Fault Flag
LMU Inform
Fault Flag
LMU Inform
y
sp
Addition
D
Items (1
in sectio
d using switch
tches relate to
CB
nic
ribe
a
Item (5) is co
require RS232
require RS232
All other items are configured using the handset terminal.
The TC12 Family Tree part number is 667/DZ/22600/000. This shows the
structure of part numbers within the TC12 system. The top level part number
the TC12 Free-standing OTU is 667/1/22670/000.
Drawing 667/GA/22670/000 shows the mechanical arrangement of the TC12 OTU.
The layout of the mechanical rac
structure of part numbers within the TC12 system. The top level part number
the TC12 Free-standing OTU is 667/1/22670/000.
Drawing 667/GA/22670/000 shows the mechanical arrangement of the TC12 OTU.
The layout of the mechanical rac
N
backplanes.
on of the rack will a
backplanes. The double backplane is now obsole
Note 2:If a TC12 OTU is to be fitted into Microsense pol
controller then use kit 667/1/22945/000 that contains the brackets and
fixings required.
fixings required.
Figure 18 and Figure 19 are diagrams of t
Figure 18 corresponds to a PCB that oper
link only. Figure 19 corresponds to a P
modem or an RS232 communications link.
The position of the switches, connectors, fuses and status LEDs are shown.
Ensure that the correct variant of the PCB has been supplied.
Figure 18 corresponds to a PCB that oper
link only. Figure 19 corresponds to a P
modem or an RS232 communications link.
The position of the switches, connectors, fuses and status LEDs are shown.
Ensure that the correct variant of the PCB has been supplied.
666/HE/43100/000
Page 63
Issue 9