Futaba 10CAG Manual De Instrucciónes
68
LINEAR PROGRAMMABLE MIXES (PROG.MIX1-4):
Sample reasons to use linear programmable mixes:
• To correct bad tendencies of the aircraft (such as rolling in response to rudder input).
• To operate 2 or more servos for a single axis (such as two rudder servos).
7RDXWRPDWLFDOO\FRUUHFWIRUDSDUWLFXODUDFWLRQ VXFKDVORZHULQJHOHYDWRUZKHQÀDSVDUHORZHUHG
7RRSHUDWHDVHFRQGFKDQQHOLQUHVSRQVHWRPRYHPHQWLQD¿UVWFKDQQHO VXFKDVLQFUHDVLQJWKHDPRXQWRIVPRNHRLOLQ
• To correct bad tendencies of the aircraft (such as rolling in response to rudder input).
• To operate 2 or more servos for a single axis (such as two rudder servos).
7RDXWRPDWLFDOO\FRUUHFWIRUDSDUWLFXODUDFWLRQ VXFKDVORZHULQJHOHYDWRUZKHQÀDSVDUHORZHUHG
7RRSHUDWHDVHFRQGFKDQQHOLQUHVSRQVHWRPRYHPHQWLQD¿UVWFKDQQHO VXFKDVLQFUHDVLQJWKHDPRXQWRIVPRNHRLOLQ
response to more throttle application, but only when the smoke switch is active).
7RWXUQRIIUHVSRQVHRIDSULPDU\FRQWUROLQFHUWDLQFLUFXPVWDQFHV VXFKDVVLPXODWLQJRQHHQJLQHÀDPLQJRXWRQDWZLQ
or throttle-assisted rudder turns, also with a twin).
Adjustability:
• Defaults: The 4 programmable mixes default to the most frequently used mixes for simplicity. If you want to use one of
• Defaults: The 4 programmable mixes default to the most frequently used mixes for simplicity. If you want to use one of
these mixes, simply select that mix number so that the master and slave servos are already selected for you.
• PROG.MIX1 aileron-to-rudder for coordinated turns
• PROG.MIX2
• PROG.MIX2
HOHYDWRUWRÀDSIRUWLJKWHUORRSV HELI mixes default to elev-to-pitch.)
• PROG.MIX3
ÀDSWRHOHYDWRUWRFRPSHQVDWHSLWFKLQJZLWKÀDSV HELI mixes default to pitch-to-elev.)
• PROG.MIX4 throttle-to-rudder ground handling compensation
•Channels available to mix: All four mixes may use any combination of CH1-8. (CH9-10 are not proportional and cannot
be mixed.) Offset and dials may also be set to the master channels. (see below.)
•Master: the controlling channel. The channel whose movement is followed by the slave channel.
•Another channel: Most mixes follow a control channel. (Ex: rudder-to-ailerons, 25%, no switch, corrects roll
coupling.)
MASTER
SLAVE
LINK
TRIM
SWITCH
POSITION
RATE
OFFSET
RUDD
AILE
ON
OFF
ANY
NULL
25%
0
•Offset as master: To create an OFFSET
PL[VHWWKHPDVWHUDV2)67 ([ PRYHÀDSHURQVDVÀDSVRIWKHLUWRWDO
throw when SWITCH C is in down position.)
MASTER
SLAVE
LINK
TRIM
SWITCH
POSITION
RATE
OFFSET
OFST
FLAP
ON
1$
C
DOWN
20%
0
• Dial as master: To directly effect one servo’s position by moving a dial, set the master as the desired dial.
(Ex: create a second throttle trim on left slider.)
MASTER
SLAVE
LINK
TRIM
SWITCH
POSITION
RATE
OFFSET
VR(D)
THRO
OFF
1$
ANY
NULL
5%
0
•Slave: the controlled channel. The channel that is moved automatically in response to the movement of the master
channel. The second channel in a mix’s name (i.e. aileron-to-rudder).
•Link: link this programmable mix with other mixes.
Ex: PMIX FLAP-ELEVATOR
PL[LQJWRFRUUHFWIRUEDOORRQLQJZKHQÀDSVDUHORZHUHGEXWPRGHOKDVD9WDLO:LWKRXWLINK,
Your 10CG contains four separate linear programmable mixes. (Note that mixer
#5-8’s mixing RATEs are set with a 5-point curve. HELI has mixer #5-6's mixing.
see CURVE MIXES, p. 71.)
#5-8’s mixing RATEs are set with a 5-point curve. HELI has mixer #5-6's mixing.
see CURVE MIXES, p. 71.)
There are a variety of reasons you might want to use these mixes. A few are
listed here. All of the adjustable parameters are listed below, but don’t let them
VFDUH\RX)RU\RXU¿UVWIHZWLPHVH[SHULPHQWLQJZLWKPL[HVMXVWWXUQRQWKH
default mixes, adjust them how you think they need to be, then use the servo
screen to check and see if you were correct. As with all functions, a sample
setup follows, step by step, to assist you.
listed here. All of the adjustable parameters are listed below, but don’t let them
VFDUH\RX)RU\RXU¿UVWIHZWLPHVH[SHULPHQWLQJZLWKPL[HVMXVWWXUQRQWKH
default mixes, adjust them how you think they need to be, then use the servo
screen to check and see if you were correct. As with all functions, a sample
setup follows, step by step, to assist you.