ALTINEX MULTI-TASKER MT109-102 Manual De Usuario
MULTI-TASKER™
400-0343-003
18
18
38. [RMG]
This command may be used to delete an entire
group, or all groups.
group, or all groups.
REMOVE ONE GROUP MEMBERS
Remove all the members from the group,
effectively deleting the group.
effectively deleting the group.
Command Format: [RMGkUi]
Gk = Group number (k = # from 1-8)
Ui
= Unit ID (i = # from 0-9)
Example:
Group 1 consists of the cards located in slots
number 1, 2 and 3. Remove all cards from the
group by sending the command [RMG1]. The
system will return the following feedback:
number 1, 2 and 3. Remove all cards from the
group by sending the command [RMG1]. The
system will return the following feedback:
G1=EMPTY
REMOVE ALL GROUPS
Remove all the members from every group,
effectively deleting all groups.
effectively deleting all groups.
Command Format: [RMG
ÜUi]
Ui
= Unit ID (i = # from 0-9)
Example:
Group 1 consists of cards 1 and 2. Group 2
consists of cards 1, 2, 3, 4 and 5. Delete all the
groups by sending the command [RMG
consists of cards 1, 2, 3, 4 and 5. Delete all the
groups by sending the command [RMG
Ü]. The
system will return the following feedback:
G1-G8:EMPTY
39. [RD]
This command reads and then displays the
members in each group.
members in each group.
Command Format: [RDGkUi]
Gk = Group number (k = # from 1-8)
Ui
= Unit ID (i = # from 0-9)
Example:
The cards in slots 1, 2 and 19 are part of
group 5. Read the member data for group 5, by
sending the command [RDG5]. The system will
return feedback as follows:
group 5. Read the member data for group 5, by
sending the command [RDG5]. The system will
return feedback as follows:
G1=C1C2C19
The feedback shows G1 (Group 1) and then the
cards that make up Group 1. In this case,
Group 1 includes C1, C2 and C19.
cards that make up Group 1. In this case,
Group 1 includes C1, C2 and C19.
40. [CLRG]
This command clears the members for a single
group or for all groups. The clear command
restores the cards to default settings and is the
equivalent to sending the [CLR] command to
each individual card.
group or for all groups. The clear command
restores the cards to default settings and is the
equivalent to sending the [CLR] command to
each individual card.
NOTE: Since this command is sending the
[CLR] command to its group members,
each card will display its own reset
message, if any.
each card will display its own reset
message, if any.
Command Format: [CLRGkUi]
Gk = Group ID (k = # from 1-8, or
Ü for all)
Ui
= Unit ID (i = # from 0-9)
Example:
1)
To clear group 1 of Unit ID 0, send the
[CLRG1] command. This command clears
the members for the specified group only.
the members for the specified group only.
2)
To clear all groups of Unit ID 1, send the
[CLRG
ÜU1] command.
41. [CLM]
This command removes the members in a
group and leaves the group empty. It is
equivalent to sending the [RMGkUi] command
without card references.
group and leaves the group empty. It is
equivalent to sending the [RMGkUi] command
without card references.
Command Format: [CLMGkUi]
Gk = Group number (k = # from 1-8)
Ui
= Unit ID (i = # from 0-9)