DSCover Satellite Products Home Security System SCW904x Manual De Usuario
Section 9: Testing & Troubleshooting
49
Trouble [4] Failure to Communicate
Panel fails to communicate one or more
events to central station
events to central station
Connect a headset to TIP and RING of the control panel. Monitor for
the following conditions:
•
•
Continuous dial tone
• Reverse TIP and RING
• Reverse TIP and RING
•
Recorded operator message comes on
• Verify correct phone number is programmed
• Dial the number programmed using a regular telephone to
• Verify correct phone number is programmed
• Dial the number programmed using a regular telephone to
determine if a [9] must be dialed or if 800 service is blocked.
•
Panel does not respond to handshakes.
• Verify the format programmed is supported by the central
• Verify the format programmed is supported by the central
station.
•
Panel transmits data multiple times without receiving a
handshake
• Verify that the account number and reporting codes are
handshake
• Verify that the account number and reporting codes are
correctly programmed.
NOTE:
Contact ID and Pulse formats
•
Contact ID and Pulse formats
•
Program a HEX [A] to transmit a digit [0]
SIA format
•
•
Program a digit [0] to transmit a digit [0]
Trouble [5] Zone Fault
Press [5] to determine specific zones with a Fault trouble
Hard-wired zone fault condition present.
A short circuit is present on one or more
zones with double end-of-line resistors
enabled
A short circuit is present on one or more
zones with double end-of-line resistors
enabled
•
Remove the wire leads from I/O and COM terminals and
measure the resistance of the wire leads.
measure the resistance of the wire leads.
Connect a 5.6K resistor (Green, Blue, Red) across the I/O and
COM terminals. Verify the trouble condition clears.
COM terminals. Verify the trouble condition clears.
One or more wireless devices have not
checked in within the programmed time
checked in within the programmed time
•
Perform a Module Placement Test – Program Section [904] and
verify the wireless device is in a good location.
• If bad test results occur, test the wireless device in another
verify the wireless device is in a good location.
• If bad test results occur, test the wireless device in another
location
• If the wireless device now tests good, the original mounting
location is bad
• If the wireless device continues to give bad test results
replace the wireless device.
Trouble [6] Zone Tamper Press [6] to determine specific zones with a Tamper trouble
An open circuit is present on one or
more zones with double end-of-line
resistors enabled
more zones with double end-of-line
resistors enabled
•
Remove the wire leads from I/O and COM terminals and
measure the resistance of the wire leads.
measure the resistance of the wire leads.
•
Connect a 5.6K resistor (Green, Blue, Red) across the I/O and
COM terminals.
• Verify the trouble condition clears.
COM terminals.
• Verify the trouble condition clears.
A tamper condition is present on one or
more wireless devices
more wireless devices
•
Ensure device cover is secure
•
Ensure device is correctly mounted for wall tamper operation
•
Violate, then restore the tamper:
• If tamper condition persists then replace wireless device
• If tamper condition persists then replace wireless device
Trouble [7] Wireless Device Low Battery Press [7] to scroll through specific devices with a Low Battery Trouble
1st press
– Wireless Zones
2nd press
– Wireless Keys
One or more wireless devices has a low
battery
battery
NOTE: The event will not be logged to
the event buffer until the wireless device
low battery delay time expires
Program Section [377] Opt 9
the event buffer until the wireless device
low battery delay time expires
Program Section [377] Opt 9
Replace Battery
•
Verify zone operation
•
Verify that tamper and low battery condition is cleared and
reported
reported
NOTE: Replacing batteries will cause a tamper. Replacing cover will
restore the tamper causing the associated reporting codes to be sent
to the Central Station.
restore the tamper causing the associated reporting codes to be sent
to the Central Station.
Trouble [8] Loss of Clock/Date
The main panel internal clock is not set
To program the time and date:
•
•
Enter [
✱][6][Master Code] then Press [1]
•
Enter the time and date (in military) using the following format:
HH:MM MM/DD/YY
HH:MM MM/DD/YY
Example.
For 6:00 pm, Nov. 30, 2007
For 6:00 pm, Nov. 30, 2007
Enter: [18] [00] [11] [30] [07]
WWW.DIYALARMFORUM.COM