Behringer Stereo System DI4000 Manual De Usuario
7
ULTRA-DI PRO DI4000 User Manual
2.2 Converting the output of a keyboard /
DJ-mixer / headphone plug
DJ-mixer / headphone plug
Out
Out
In
In
Microphone Inputs Pan left and right
Fig. 2.2: DJ-mixer 2 x DI box mixer
This configuration can be used with a keyboard, DJ-mixer, headphone output,
drum kit or any (stereo or mono) line source. In all cases where you want to run
long lines, for instance to the FOH (Front Of House) desk. The signal can be linked
through to another amplifier, if the keyboard player/ DJ/etc. wants to have a
monitor connected independent of the foldback mix. The ULTRA-DI PRO acts as
both a ground isolator and an unbalanced to balanced converter.
2.3 Converting a microphone signal
Out
In
Fig. 2.3: Connecting a microphone
Sometimes all that’s available (especially when all other mics are in use) is an
unbalanced high impedance microphone with an unbalanced jack. With the
ULTRA-DI PRO long cable runs to the console can be established without fear
of picking up noise and hum. Just plug the jack into the input and connect the
output to the console’s mic input.
2.4 Tapping a signal from a power
amplifier output
amplifier output
When no line out is available it is possible to connect an amplifier output directly
to the DI4000 (for example, recording direct from a guitar amplifier, TV-speaker,
etc). It is possible to connect the output, i.e. an extra speaker output, of up to
3000 Watts to the ULTRA-DI PRO without fear of overloading. Pay attention to the
two -20 dB buttons on the ULTRA-DI PRO! Both must be depressed if an amplifier
output is connected to the DI4000 input.
In
Out
+red or positive post
-black or negative post
-20 / -40 dB!
Fig. 2.4: Connection to an amplifier output
◊
Always make sure the GROUND LIFT is on (no ground link)
when connecting to speaker terminals. This prevents accidental
short‑circuiting of the amplifier output. Also make sure the tip of the
input jack is connected to the red terminal and that the metal housing
of the DI4000 has no contact with other equipment.
when connecting to speaker terminals. This prevents accidental
short‑circuiting of the amplifier output. Also make sure the tip of the
input jack is connected to the red terminal and that the metal housing
of the DI4000 has no contact with other equipment.
3. Installation
Your BEHRINGER ULTRA-DI PRO was carefully packed in the factory and
the packaging was designed to protect the unit from rough handling.
Nevertheless, we recommend that you carefully examine the packaging and its
contents for any signs of physical damage, which may have occurred in transit.
◊
If the unit is damaged, please do not return it to us, but notify your
dealer and the shipping company immediately, otherwise claims for
damage or replacement may not be granted. Shipping claims must be
made by the consignee.
dealer and the shipping company immediately, otherwise claims for
damage or replacement may not be granted. Shipping claims must be
made by the consignee.
3.1 Rack mounting
The BEHRINGER ULTRA-DI PRO fits into one standard 19" rack unit of space.
Please allow at least an additional 4" depth for the connectors on the back panel.
◊
Be sure that there is enough air space around the unit for cooling and
please do not place the ULTRA‑DI PRO on high temperature devices such
as power amplifiers etc. to avoid overheating.
please do not place the ULTRA‑DI PRO on high temperature devices such
as power amplifiers etc. to avoid overheating.
3.2 Mains connection
The mains connection of the ULTRA-DI PRO is made by using a mains cable
and a standard IEC receptacle. It meets all of the international safety
certification requirements.
◊
Please make sure that all units have a proper ground connection.
For your own safety, it is advisable not to remove the ground
connection within the units or at the supply, or fail to make this
connection at all.
For your own safety, it is advisable not to remove the ground
connection within the units or at the supply, or fail to make this
connection at all.