Country Home Products DR LEAF & LAWN VACUUM Manual De Usuario
Premier model: (Kit No. 18795)
Figure 8
Figure 9
Pre-formed Edge
Outer Panel
Inner Panel
Slide
Side Spacer
Shown with Top removed
Spacer Tube
Pre-formed Notch
1. Remove the Rear Panel of the Collector Box by
releasing the six (6) Flexible Latches and lift it off the
pins protruding on the top corners.
pins protruding on the top corners.
2. Install the supplied Bagger Spacers inside the
Collector Box by first releasing the Flexible Latches
holding down the Centrifugal Separator (top).
holding down the Centrifugal Separator (top).
3. Install a side Bagger Spacer on the left Side Panel of
the Collector Box by inserting the formed edge of the
Spacer in between the inner and outer wall of the left
Side Panel of the Collector Box (Figure 8).
Spacer in between the inner and outer wall of the left
Side Panel of the Collector Box (Figure 8).
Tip: Raise the Centrifugal Separator (top) just enough
and start at the back of the Collector Box left Side
Panel, hooking the formed edge of the Bagger Spacer
over the inner panel and in between the Outer Panel
and Inner Panel, and sliding the Spacer along toward
the front until the support is completely inside the
Collector Box (Figure 8).
Panel, hooking the formed edge of the Bagger Spacer
over the inner panel and in between the Outer Panel
and Inner Panel, and sliding the Spacer along toward
the front until the support is completely inside the
Collector Box (Figure 8).
4. Repeat this procedure for installing a side Bagger Spacer
on the right Side Panel.
5. Install a Bagger Spacer Tube in the front of the
Collector Box by raising the Centrifugal Separator
(top) just enough to insert it into the Pre-Formed
Notches in the left and right Bagger Spacers. Note
the shape of the Spacer Tube; it will only go in one
way. The outside surface of the Spacer Tube must be
perpendicular to the Top (Figure 9).
(top) just enough to insert it into the Pre-Formed
Notches in the left and right Bagger Spacers. Note
the shape of the Spacer Tube; it will only go in one
way. The outside surface of the Spacer Tube must be
perpendicular to the Top (Figure 9).
6. Form the individual Leaf Bag Holders into boxes and
insert a biodegradable leaf bag or 30 gal. Heavy-Duty
trash bag (supplied by the user) into each box, folding
the top of the bag (Figure 6) over the top edge of the
box.
trash bag (supplied by the user) into each box, folding
the top of the bag (Figure 6) over the top edge of the
box.
NOTE: Fold down the corners of the Bag Holder to stiffen
the assembly (Figure 7).
7. Place the six (6) boxes into the Collector Box starting
at the front and working toward the rear.
Tip: Installation is easier if the outside boxes are placed
first in each row, followed by inserting the center box
between them (Figure 6).
between them (Figure 6).
8. Install a Bagger Spacer Tube at the rear of the
Collector Box by raising the Centrifugal Separator
(top) just enough to insert it into the Pre-Formed
Notches in the left and right Bagger Spacers. Again,
note the shape of the Spacer Tube; it will only go in
one way. The outside surface of the Spacer Tube
must be perpendicular to the Top (Figure 8).
(top) just enough to insert it into the Pre-Formed
Notches in the left and right Bagger Spacers. Again,
note the shape of the Spacer Tube; it will only go in
one way. The outside surface of the Spacer Tube
must be perpendicular to the Top (Figure 8).
9. Re-hook the Centrifugal Separator (top) Latches and
replace the Rear Panel by re-hanging it on the pins
protruding on the top corners, and then re-hook the
six (6) Flexible Latches.
protruding on the top corners, and then re-hook the
six (6) Flexible Latches.
Side Spacer
Front
Perpendicular surface
facing out
facing out
Rear
7 DR
®
LEAF and LAWN VACUUM Optional Accessories