Breckwell P4000 Manual De Usuario
D.
VERTICALLY INTO EXISTING MASONRY
FIREPLACE
FIREPLACE
NOTE: See “VENTING” and follow L-Vent chimney
manufacturer’s instructions.
1.
Have the masonry chimney inspected by a qualified
chimney sweep or installer to determine its structural
condition.
chimney sweep or installer to determine its structural
condition.
2.
You will need a pipe length equal to the chimney
height from the hearth. If outside combustion air is to
be used, you will need a pipe length equal to the
chimney height plus 18 inches.
height from the hearth. If outside combustion air is to
be used, you will need a pipe length equal to the
chimney height plus 18 inches.
3.
Install a blanking plate and the chimney pipe, and if
used the outside air pipe, as shown in Figure 9.
used the outside air pipe, as shown in Figure 9.
4.
Attach the L-Vent adapter, a section of pipe and
clean out tee, making sure the clean out tee is
centered in the chimney flue area.
clean out tee, making sure the clean out tee is
centered in the chimney flue area.
5.
Position the stove, adhering to the clearances in
Figures 1 & 2.
Figures 1 & 2.
6.
Measure and build chimney top plate. Cut out holes
for chimney pipe, and if used the outside air pipe.
Install and seal with non-hardening mastic to prevent
water leakage. Install vent cap.
for chimney pipe, and if used the outside air pipe.
Install and seal with non-hardening mastic to prevent
water leakage. Install vent cap.
E.
INSTALLATION THROUGH SIDE OF MASONRY
CHIMNEY
CHIMNEY
NOTE: See “VENTING” and follow L-Vent chimney
manufacturer’s instructions.
1.
Position the stove, adhering to the clearances in
Figures 1 & 2. Mark the center of the hole where the
pipe is to pierce the masonry chimney.
Figures 1 & 2. Mark the center of the hole where the
pipe is to pierce the masonry chimney.
2.
It will be necessary to break out the masonry around
the location of the pipe center mark. Use a 4-inch
diameter hole for 3-inch pipe and 5-inch diameter
hole for 4-inch pipe.
the location of the pipe center mark. Use a 4-inch
diameter hole for 3-inch pipe and 5-inch diameter
hole for 4-inch pipe.
3.
Measure and build chimney top plate. Cut out holes
for chimney pipe, and if used the outside air pipe.
for chimney pipe, and if used the outside air pipe.
4.
Install the tee on the bottom of the vertical pipe
system and lower it down the chimney until the
center branch of the tee is level with the center of
the hole in the masonry, as shown in Figure 10.
system and lower it down the chimney until the
center branch of the tee is level with the center of
the hole in the masonry, as shown in Figure 10.
5.
Install and seal the top plate from step 3 with non-
hardening mastic. Slip the storm collar over the pipe,
and while holding the pipe at the proper elevation,
affix the collar with a minimum of three ¼” stainless
steel sheet metal screws. Seal all joints and seams
around the collar.
hardening mastic. Slip the storm collar over the pipe,
and while holding the pipe at the proper elevation,
affix the collar with a minimum of three ¼” stainless
steel sheet metal screws. Seal all joints and seams
around the collar.
6.
Connect the horizontal pipe by pushing it through
the hole in the masonry and lining it up with the
branch in the tee. Push the pipe into the tee while
twisting it to lock it into the tee.
the hole in the masonry and lining it up with the
branch in the tee. Push the pipe into the tee while
twisting it to lock it into the tee.
7.
If desired, once the horizontal pipe is in place, the
space between the pipe and masonry may be filled
with high-temperature grout.
space between the pipe and masonry may be filled
with high-temperature grout.
8.
Install the trim collar. An adjustable pipe length and
adapter may be needed to finish the connection to
the stove.
adapter may be needed to finish the connection to
the stove.
FIGURE 9
FIGURE 10
INSTALLATION
9