Lopi 1080 Manual De Usuario
8
Operation
© Travis Industries
4070710
100-01194_000
Starting the Fireplace for the First Time
•
Burn the heater at a high setting for an extended period (up to 48 hours). This will cure the
painted surfaces. Fumes from the paint curing and oil burning off the steel will occur. This is
normal. We recommend opening a window to vent the room.
painted surfaces. Fumes from the paint curing and oil burning off the steel will occur. This is
normal. We recommend opening a window to vent the room.
•
Condensation may appear on the glass each time you start the fireplace - this is normal.
•
Blue Flames will occur on the fireplace when it first comes on. After fifteen minutes the flames
will turn a more realistic yellow and orange color.
will turn a more realistic yellow and orange color.
Adjusting the Flame Height
Adjustment with the Wall Switch (recommended)
With the fireplace in manual mode and the fireplace on, click the “HI” or “LO” button until the
desired flame height is achieved.
desired flame height is achieved.
Adjustment with the Remote
With the fireplace in manual mode and the fireplace on, click and hold the “ON” button until the
desired flame height is achieved. Each time the “ON” button is held down, the flame height will
toggle between getting taller (“HI” will be displayed on the LCD screen) or getting smaller (“LO”
will be displayed on the LCD screen).
desired flame height is achieved. Each time the “ON” button is held down, the flame height will
toggle between getting taller (“HI” will be displayed on the LCD screen) or getting smaller (“LO”
will be displayed on the LCD screen).
Continuous Pilot – For Very Cold Conditions
This fireplace can be configured to run with an intermittent or continuous (standing) pilot. For
normal conditions we recommend using the intermittent pilot (pilot is on only when the main
burner is on). For extremely cold conditions we recommend using a continuous pilot (pilot is on all
the time). By having the pilot on continuously, a draft is established in the vent, allowing the main
burner to turn on with less air-flow disruption.
normal conditions we recommend using the intermittent pilot (pilot is on only when the main
burner is on). For extremely cold conditions we recommend using a continuous pilot (pilot is on all
the time). By having the pilot on continuously, a draft is established in the vent, allowing the main
burner to turn on with less air-flow disruption.
Setting the Fireplace to Continuous Pilot
Press and hold down the “OFF Continuous Pilot” button on the remote for 10 seconds. “PILOT” will
appear on the LCD screen, indicating that the fireplace is configured for a continuous pilot. To
configure the fireplace for an intermittent pilot, press and hold down the “OFF Continuous Pilot”
button on the remote for 10 seconds until the “PILOT” is no longer visible on the LCD screen.
appear on the LCD screen, indicating that the fireplace is configured for a continuous pilot. To
configure the fireplace for an intermittent pilot, press and hold down the “OFF Continuous Pilot”
button on the remote for 10 seconds until the “PILOT” is no longer visible on the LCD screen.
Normal Operating Odors
This appliance has several areas that reach high temperatures. Dust or other particles on these
areas may burn and create an odor. This is normal during start-up. You may notice the smell is
more acute if the appliance was left idle for a long period.
areas may burn and create an odor. This is normal during start-up. You may notice the smell is
more acute if the appliance was left idle for a long period.
Power Outages
This fireplace utilizes household power (110 VAC) to power the receiver module and intermittent
pilot system. A separate battery box is included to provide power for the adjustable flame height
and in case of power outages. If you experience a power outage and the unit does not operate,
make sure to replace the AA batteries in the battery box (see “Battery Installation” on page 19).
pilot system. A separate battery box is included to provide power for the adjustable flame height
and in case of power outages. If you experience a power outage and the unit does not operate,
make sure to replace the AA batteries in the battery box (see “Battery Installation” on page 19).