Manual De UsuarioTabla de contenidos1. INTRODUCTION11.1. Contents of the Manual11.2. Who Should Use This Manual?11.3. Special Notices11.3.1. Warning11.3.2. Caution11.3.3. Note12. General Description22.1. Optional Features22.2. Specifications23. Projector installation and Assembly33.1. Unpacking the Projector33.2. Installation33.3. Electrical Connections33.3.1. Solar Cell Wiring33.3.2. A-C Projector Wiring34. OPERATING THE PROJECTOR44.1. General44.2. Pre-Operating Procedures44.2.1. Flywheel Installation44.2.2. Turret Installation44.2.3. Lens Installation44.3. Film Threading and Operating Procedure45. MAINTENANCE55.1. General Maintenance55.2. Visual Inspection55.3. Cleaning55.4. Removal of Assemblies55.4.1. Removal of the Trap and Gate Assembly55.4.2. Outer Timing Belt55.4.3. Inner Timing Belt55.4.4. Shutter Timing Belt55.4.5. Upper, Center, and Lower Constant-Speed Sprocket Assemblies55.4.6. Ultramittent Assembly55.4.7. Removal of LED Soundhead and Solar Cell Assembly55.4.8. Removal of Digital Soundhead Assembly55.4.9. Removal of Electric Changeover Assembly55.4.10. Removal of Shutter Driver Assembly55.4.11. Removal of Motor Assembly55.4.12. Removal of Fan55.4.13. Removal of Framing Lamp56.1. LED Soundhead Alignment and Adjustments66.1.1. Preliminary Procedures66.1.2. Cell Positioning: Vertical Alignment66.1.3. Horizontal Alignment66.1.4. Focus and Azimuth66.1.5. Alignment Verification66.1.6. Performance Check: Crosstalk66.1.7. Illumination Uniformity66.1.8. Final Check66.2. Digital Soundhead Alignment66.2.1. Preliminary Steps66.2.2. Alignment Procedure66.3. Dashpot Adjustment66.4. Inner, Outer, and Shutter Timing Belt Adjustment66.4.1. Inner Timing Belt66.4.2. Shutter Timing Belt66.4.3. Outer Timing Belt66.5. Shutter Timing66.6. The CHRISTIE Dual-Lens Turret66.6.1. General Description66.6.2. The Manual Turret System66.6.3. The Automatic Turret System66.6.4. Timing Adjustments – Turret and Aperture Motor66.7. Optical Image Alignment and Adjustment Procedures67. Troubleshooting Procedures77.1. Motor77.1.1. SYMPTOM: Motor Not Working77.2. Ultramittent Assembly77.2.1. SYMPTOM: Excessive Ticking77.2.2. SYMPTOM: Excessive Film Noise77.2.3. SYMPTOM: Film Instability (Jump)77.2.4. SYMPTOM: Shutter Streaking77.3. Constant-Speed Sprocket Assembly77.3.1. SYMPTOM: Excessive Noise77.3.2. SYMPTOM: Film Sprocket Hole Damage77.3.3. SYMPTOM: Sprocket Riding77.4. Belts77.4.1. SYMPTOM: Excessive Noise77.4.2. SYMPTOM: Excessive Belt Dust77.4.3. SYMPTOM: Excessive Belt Failure77.5. Changeover Assembly77.5.1. SYMPTOM: Operating Inconsistently77.5.2. SYMPTOM: Not Operating77.6. Shutter Drive (Shutter Driver and Jackshaft System)77.6.1. SYMPTOM: Excessive Noise77.6.2. SYMPTOM: Shutter Streak77.7. Trap and Gate Assembly77.7.1. SYMPTOM: Excessive Jump and Weave77.7.2. SYMPTOM: Aperture Binding77.8. Lens Turret77.8.1. SYMPTOM: Not Rotating77.8.2. SYMPTOM: Focus Knob Inoperative77.8.3. SYMPTOM: Turret Hinge Too Loose77.8.4. SYMPTOM: Turret Hinge Too Tight7Figure 2-1: Table of Equipment Specifications2Figure 2-2: Projector, Front View2Figure 2-3: Projector, Rear View2Figure 3-1: Installing the Projector3Figure 3-2: Tools and Materials Required for Assembly and Maintenance3Figure 3-3: Projector Wiring Diagram (50- and 60-Hz models)3Figure 3-4: Table of A-C Terminal Connections3Figure 4-1: Threading Diagram4Figure 5-1: Schedule for Periodic Maintenance Operations5Figure 5-2: Outer Timing Belt5Figure 5-3: Inner Timing Belt5Figure 5-4: Shutter Timing Belt5Figure 6-1: Analog Reader Alignment and Adjustments6Figure 6-2: Digital Reader Assembly6Figure 6-3: Dual Turret (Front View)6Figure 6-4: Dual Turret (Rear View)6Tamaño: 2 MBPáginas: 85Language: EnglishManuales abiertas