Manuali utente per Christie Digital Systems P35GPS-MT

Sommario

• 1. INTRODUCTION

  1
• 1.1. Contents of the Manual

  1
• 1.2. Who Should Use This Manual?

  1
• 1.3. Special Notices

  1
• 1.3.1. Warning

  1
• 1.3.2. Caution

  1
• 1.3.3. Note

  1
• 2. General Description

  2
• 2.1. Optional Features

  2
• 2.2. Specifications

  2
• 3. Projector installation and Assembly

  3
• 3.1. Unpacking the Projector

  3
• 3.2. Installation

  3
• 3.3. Electrical Connections

  3
• 3.3.1. Solar Cell Wiring

  3
• 3.3.2. A-C Projector Wiring

  3
• 4. OPERATING THE PROJECTOR

  4
• 4.1. General

  4
• 4.2. Pre-Operating Procedures

  4
• 4.2.1. Flywheel Installation

  4
• 4.2.2. Turret Installation

  4
• 4.2.3. Lens Installation

  4
• 4.3. Film Threading and Operating Procedure

  4
• 5. MAINTENANCE

  5
• 5.1. General Maintenance

  5
• 5.2. Visual Inspection

  5
• 5.3. Cleaning

  5
• 5.4. Removal of Assemblies

  5
• 5.4.1. Removal of the Trap and Gate Assembly

  5
• 5.4.2. Outer Timing Belt

  5
• 5.4.3. Inner Timing Belt

  5
• 5.4.4. Shutter Timing Belt

  5
• 5.4.5. Upper, Center, and Lower Constant-Speed Sprocket Assemblies

  5
• 5.4.6. Ultramittent Assembly

  5
• 5.4.7. Removal of LED Soundhead and Solar Cell Assembly

  5
• 5.4.8. Removal of Digital Soundhead Assembly

  5
• 5.4.9. Removal of Electric Changeover Assembly

  5
• 5.4.10. Removal of Shutter Driver Assembly

  5
• 5.4.11. Removal of Motor Assembly

  5
• 5.4.12. Removal of Fan

  5
• 5.4.13. Removal of Framing Lamp

  5
• 6.1. LED Soundhead Alignment and Adjustments

  6
• 6.1.1. Preliminary Procedures

  6
• 6.1.2. Cell Positioning: Vertical Alignment

  6
• 6.1.3. Horizontal Alignment

  6
• 6.1.4. Focus and Azimuth

  6
• 6.1.5. Alignment Verification

  6
• 6.1.6. Performance Check: Crosstalk

  6
• 6.1.7. Illumination Uniformity

  6
• 6.1.8. Final Check

  6
• 6.2. Digital Soundhead Alignment

  6
• 6.2.1. Preliminary Steps

  6
• 6.2.2. Alignment Procedure

  6
• 6.3. Dashpot Adjustment

  6
• 6.4. Inner, Outer, and Shutter Timing Belt Adjustment

  6
• 6.4.1. Inner Timing Belt

  6
• 6.4.2. Shutter Timing Belt

  6
• 6.4.3. Outer Timing Belt

  6
• 6.5. Shutter Timing

  6
• 6.6. The CHRISTIE Dual-Lens Turret

  6
• 6.6.1. General Description

  6
• 6.6.2. The Manual Turret System

  6
• 6.6.3. The Automatic Turret System

  6
• 6.6.4. Timing Adjustments – Turret and Aperture Motor

  6
• 6.7. Optical Image Alignment and Adjustment Procedures

  6
• 7. Troubleshooting Procedures

  7
• 7.1. Motor

  7
• 7.1.1. SYMPTOM: Motor Not Working

  7
• 7.2. Ultramittent Assembly

  7
• 7.2.1. SYMPTOM: Excessive Ticking

  7
• 7.2.2. SYMPTOM: Excessive Film Noise

  7
• 7.2.3. SYMPTOM: Film Instability (Jump)

  7
• 7.2.4. SYMPTOM: Shutter Streaking

  7
• 7.3. Constant-Speed Sprocket Assembly

  7
• 7.3.1. SYMPTOM: Excessive Noise

  7
• 7.3.2. SYMPTOM: Film Sprocket Hole Damage

  7
• 7.3.3. SYMPTOM: Sprocket Riding

  7
• 7.4. Belts

  7
• 7.4.1. SYMPTOM: Excessive Noise

  7
• 7.4.2. SYMPTOM: Excessive Belt Dust

  7
• 7.4.3. SYMPTOM: Excessive Belt Failure

  7
• 7.5. Changeover Assembly

  7
• 7.5.1. SYMPTOM: Operating Inconsistently

  7
• 7.5.2. SYMPTOM: Not Operating

  7
• 7.6. Shutter Drive (Shutter Driver and Jackshaft System)

  7
• 7.6.1. SYMPTOM: Excessive Noise

  7
• 7.6.2. SYMPTOM: Shutter Streak

  7
• 7.7. Trap and Gate Assembly

  7
• 7.7.1. SYMPTOM: Excessive Jump and Weave

  7
• 7.7.2. SYMPTOM: Aperture Binding

  7
• 7.8. Lens Turret

  7
• 7.8.1. SYMPTOM: Not Rotating

  7
• 7.8.2. SYMPTOM: Focus Knob Inoperative

  7
• 7.8.3. SYMPTOM: Turret Hinge Too Loose

  7
• 7.8.4. SYMPTOM: Turret Hinge Too Tight

  7
• Figure 2-1: Table of Equipment Specifications

  2
• Figure 2-2: Projector, Front View

  2
• Figure 2-3: Projector, Rear View

  2
• Figure 3-1: Installing the Projector

  3
• Figure 3-2: Tools and Materials Required for Assembly and Maintenance

  3
• Figure 3-3: Projector Wiring Diagram (50- and 60-Hz models)

  3
• Figure 3-4: Table of A-C Terminal Connections

  3
• Figure 4-1: Threading Diagram

  4
• Figure 5-1: Schedule for Periodic Maintenance Operations

  5
• Figure 5-2: Outer Timing Belt

  5
• Figure 5-3: Inner Timing Belt

  5
• Figure 5-4: Shutter Timing Belt

  5
• Figure 6-1: Analog Reader Alignment and Adjustments

  6
• Figure 6-2: Digital Reader Assembly

  6
• Figure 6-3: Dual Turret (Front View)

  6
• Figure 6-4: Dual Turret (Rear View)

  6