Manual De UsuarioTabla de contenidosIntroduction7Projector Features7Package Contents8Projector with Lens Cap8AC Power Cord8Projector Overview10Front View10Rear View11Bottom View11Using the Product12Control Panel12Connection Ports13Remote Control15Installing the Batteries171. Open the battery cover in the direction shown.172. Install batteries as indicated by the diagram inside the compartment.173. Close the battery cover into position.17Remote Control Operation18Connection191. Turn all equipment off before making any connections.192. Use the correct signal cables for each source.193. Ensure the cables are firmly inserted.19Connecting a computer or monitor20Connecting a computer201. Take the supplied VGA cable and connect one end to the D-Sub output socket of the computer.202. Connect the other end of the VGA cable to the Computer in 1 or Computer in 2 signal input socket on the projector.20Connecting a monitor201. Connect the projector to a computer as described in “Connecting a computer” on page 18.202. Take a suitable VGA cable (only one supplied) and connect one end of the cable to the D-Sub input socket of the video monitor.203. Connect the other end of the cable to the Monitor Out socket on the projector.20Connecting Video source devices21Connecting a Component Video source device221. Take a VGA (D-Sub) to HDTV (RCA) cable, Component Video cable or a Component Video to VGA (D-Sub) adaptor and connect the end...222. If you are using the VGA (D-Sub) to HDTV (RCA) cable and the Component Video to VGA (D-Sub) adaptor, connect the other end of...22Connecting an S-Video source device221. Take an S-Video cable and connect one end to the S-Video output socket of the Video source device.222. Connect the other end of the S-Video cable to the S-Video socket on the projector.22Connecting a composite Video source device231. Take a Video cable and connect one end to the composite Video output socket of the Video source device.232. Connect the other end of the Video cable to the Video socket on the projector.23Operation24Powering On/Off the Projector24Powering On the Projector:241. Remove the projector lens cap.242. Complete the AC power cord and peripheral signal cable(s) connections.243. Press to turn on the projector. The projector takes a minute or so to warm up.244. Turn on your source (computer, notebook, DVD, etc.). The projector automatically detects your source.24Powering Off the Projector:241. Press to turn off the projector lamp. You will see a message "Power off? Press Power again" appear on the screen.242. Press again to confirm.243. Disconnect the AC power cord from the electrical outlet and the projector.244. Do not turn on the projector right after power off.24Adjusting the Projector Height251. To raise or lower the image, press the elevator button and raise or lower the front of the projector. Release the button to lock the adjustment.252. To level the image on the screen, turn the tilt-adjustment feet to fine-tune the height.25Adjusting the Projector Zoom and Focus251. Focus the image by rotating the focus ring. A still image is recommended for focusing.252. Adjust the image size by sliding the zoom ring.25Adjusting Projection Image Size26Locking control keys271. Press on the projector or remote control.272. A confirmation message is displayed. Select Yes to confirm.27Menu Operation28How to operate311. Press MENU on the projector or Menu on the remote control to open the OSD menu.312. When OSD is displayed, use p / q to select any feature in the main menu.313. After selecting the desired main menu item, press u to enter sub-menu for feature setting.314. Use p / q to select the desired item and adjust the settings with t / u.315. Press MENU on the projector or Menu on the remote control, the screen will return to the main menu.316. To exit OSD, Press MENU on the projector or Menu on the remote control again. The OSD menu will close and the projector will automatically save the new settings.31Controlling the projector through a LAN environment38Wired connection381. Take a RJ45 cable and connect one end to the RJ45 LAN input jack of the projector and the other end to the RJ45 port on your Ethernet or router.382. Press MENU/EXIT on the projector or Menu on the remote control and then press / until the NetWork menu is highlighted.383. Highlight Wired LAN and press ENTER on the projector or Enter on the remote control.384. Make sure the Status is Connect.385. Press to highlight DHCP and press / to select On.386. Press to highlight Apply and press ENTER on the projector or Enter on the remote control.387. Please wait for around 15 - 20 seconds, and then re-enter the Wired LAN page. The IP Address, Subnet Mask, Default Gateway, and DNS settings will be displayed. Note down the IP address displayed in the IP Address row.381. Repeat steps 1-4 above.382. Press to highlight DHCP and press / to select Off.383. Contact your ITS administrator for information on the IP Address, Subnet Mask, Default Gateway, and DNS settings.384. Press to select the item you want to modify and press ENTER on the projector or Enter on the remote control.395. Press / to move the cursor and the enter the value.396. To save the settings, press ENTER on the projector or Enter on the remote control. If you do not want to save the settings, press MENU/EXIT on the projector397. or Menu on the remote control.398. Press to highlight Apply and press ENTER on the projector or Enter on the remote control.39Wireless connection401. Make sure the projector is turned on.402. Press MENU/EXIT on the projector or Menu on the remote control and then press / until the NetWork menu is highlighted.403. Highlight Wireless LAN and press ENTER on the projector or Enter on the remote control.404. Make sure the Status is Connect.405. Make sure the SSID information is displayed.406. Press to highlight Connection Mode and press / to select AP or Infrastructure. In AP mode, you need to use your computer’s wi...40Controlling the projector through a web browser411. Enter the address of the projector in the address bar of your browser and press Enter.412. The main page of the ViewSonic webpage control system appears.413. To change the language for the web pages, click the down arrow to reveal a drop down list and select a desired language.414. To download pwPresenter, click Download. See “Displaying images through pwPresenter” on page 45 for details.415. To achieve best performance, download the install mirror display driver.416. To download USB LAN driver, click Download.417. To have access to the Admin page, you need to enter a password. The default password is “0000”.428. The Crestron (eControl) page displays the Crestron eControl user interface. The eControl page provides a variety of virtual keys to control the projector or adjust the projected pictures.43Displaying images through pwPresenter47Downloading and installing pwPresenter471. Enter the main page of Network Control. See steps 1-2 on page 39 for details.472. Download pwPresenter.473. When the download is complete, install the software to your computer by clicking the exe file. Follow the on-screen instructions to complete the installation.474. Launch pwPresenter.47Using pwPresenter471. The Search page allows you to search and connect to a projector.472. The Capture screen allows you to start or pause capture screen.483. You can choose a capture mode from here.484. The Basic Setting page allows you to configure pwPresenter.495. The Advanced Setting page allows you to configure pwPresenter.506. Network Display Management displays the Device Management and pwPresenter Management information.517. Disconnect allows you to disconnect from the projector(s) by clicking the Disconnect icon.52Displaying pictures with a USB storage device531. Take a USB cable and connect the larger end to the USB A socket on the projector, and smaller end to the USB port of the device. If you are using a USB flash drive, connect it directly to the USB A socket.532. The projector automatically display the thumbnails. Or your can manually select USB Reader from the source selection bar.533. The ImageView main screen is displayed and ready to use. The main screen is displayed in Thumbnail Display Mode which shows the following four parts:534. Use the four directional buttons or page up/down button to move between pages/ folders. To Press and hold Menu and then press...53Maintenance55Cleaning the Lens55Cleaning the Projector Housing55Cleaning the Filter Cover551. Switch the projector off and unplug the AC power cord from the wall socket.552. Remove the filter cover as the illustration shown.553. Clean the filter cover.554. Replace the filter cover.555. Attach the filter cover.556. Plug the power back into the projector.55Replacing the Lamp561. Turn off the projector.572. If the projector is installed in a ceiling mount, remove it573. Unplug the power cord.574. Loosen the screw in the side of the lamp cover and remove the cover.575. Remove the screws from the lamp module, raise the handle, and lift out the module.576. Insert the new lamp module into the projector and tighten the screws.577. Replace the lamp cover and tighten the screw.578. Turn on the projector. If the lamp does not turn on after the warm-up period, try reinstalling the lamp.579. Reset the lamp hour. Refer to the “Information” menu.57Specifications58Dimensions59Ceiling mount installation59Appendix60LED Indicator Messages60Compatibility Modes61Computer:61Video:62Troubleshooting63Start-up problems63Image problems63RS-232 Command and Configuration64IR Control Code66Tamaño: 5 MBPáginas: 72Language: EnglishManuales abiertas