Heath Zenith SL-5318 Manuel D’Utilisation
598-1001-01
3
Motion
Motion
8 ft.
(2.4 m)
70 ft.
100 ft.
(21 m) (30.5 m)
Boosted
Sensor
240
°
B
O
O
S
T
MAX
MIN
RANGE
ON - TIME
DUAL BRITE
TEST 1 5 2 0
MINUTES
OFF 3 6 DUSK TO
HOUR DAWN
TEST AND ADJUSTMENT
❒
Turn on the circuit breaker and light switch.
NOTE:
Sensor has a 1
1
/
2
minute warm up period
before it will detect motion. When first turned
on, wait 1
on, wait 1
1
/
2
minutes.
Bottom of Sensor
Avoid aiming the control at:
• Objects that change temperature rapidly, such as
heating vents and air conditioners. These heat
sources could cause false triggering.
sources could cause false triggering.
• Areas where pets or traffic may trigger the control.
• Nearby large, light-colored objects reflecting light
may trigger the shut-off feature. Do not point other
lights at the sensor.
lights at the sensor.
❒
Turn the RANGE control to the mid position, Dual
Brite™ to OFF and the ON-TIME control to the
TEST position.
Brite™ to OFF and the ON-TIME control to the
TEST position.
Maximum
Maximum Range
Coverage Angle
The detector is less sensitive to motion directly towards it.
Least Sensitive
Most Sensitive
SPECIFICATIONS
Horizontal Range . . . Up to 70 ft. (21 m); 100 ft.
(30.5 m) with Range Boost.
[varies with surrounding
temperature]
[varies with surrounding
temperature]
Sensing Angle . . . . . . Up to 240
°
Electrical Load . . . . . . Up to 300 Watt Maximum In-
candescent [Up to 150 Watt
Maximum each lamp holder.]
Maximum each lamp holder.]
Power Requirements . 120 VAC, 60 Hz
Operating Modes . . . . TEST, AUTO, and MANUAL
Operating Modes . . . . TEST, AUTO, and MANUAL
MODE
Time Delay . . . . . . . . 1 , 5, 20 minutes
Dual Brite™ Timer . . . 3, 6 hours, Dusk-to-Dawn
Dual Brite™ Timer . . . 3, 6 hours, Dusk-to-Dawn
Warning - Risk of fire. Do not aim the lamps at a
combustible surface within 3 ft. (1 m).
combustible surface within 3 ft. (1 m).
❒
Loosen the clamp screw in
the sensor ball joint and gen-
tly rotate the sensor.
the sensor ball joint and gen-
tly rotate the sensor.
❒
Walk through the coverage
area noting where you are
when the lights turn on. Move
the sensor head up, down, or
sideways to change the cov-
erage area. Keep the sen-
sor at least 1" (2.5 cm) away
from the lamps.
area noting where you are
when the lights turn on. Move
the sensor head up, down, or
sideways to change the cov-
erage area. Keep the sen-
sor at least 1" (2.5 cm) away
from the lamps.
❒
Adjust the RANGE as
needed. RANGE set too high
may increase false triggering.
needed. RANGE set too high
may increase false triggering.
❒
Secure the sensor head by
tightening the clamp screw.
Do not overtighten the screw.
tightening the clamp screw.
Do not overtighten the screw.
❒
Set the amount of TIME you
want the lights to stay on after
motion is detected (1, 5, or 20 minutes).
want the lights to stay on after
motion is detected (1, 5, or 20 minutes).
❒
Set the DUAL BRITE™ switch to the amount of
time after dusk you want the lights on at low level
(Off, 3, 6 Hrs., Dusk-to-Dawn).
time after dusk you want the lights on at low level
(Off, 3, 6 Hrs., Dusk-to-Dawn).
Clamp
Screw
Screw
Ball
Joint
Joint
Aim Sensor
Down for Short
Coverage
Aim Sensor
Higher for Long
Coverage
DESA Specialty Products™ reserves the right to dis-
continue products and to change specifications at any
time without incurring any obligation to incorporate new
features in products previously sold.
continue products and to change specifications at any
time without incurring any obligation to incorporate new
features in products previously sold.