Emerson CF550ORB00 Manuel D’Utilisation
5
How to Put Your Ceiling Fan Together
(continued)
FAN MOTOR
ASSEMBLY
ASSEMBLY
CEILING
COVER
COVER
DOWNROD
RUBBER GROMMET
COUPLER COVER
Figure 3
4.
Make sure the rubber grommet is properly installed
onto the coupling cover then slide the coupler
cover onto the downrod until it rests on top of the
motor housing. Place the ceiling cover over
the downrod. Be sure both the ceiling cover and
the coupler cover are oriented correctly (Figure 3).
onto the coupling cover then slide the coupler
cover onto the downrod until it rests on top of the
motor housing. Place the ceiling cover over
the downrod. Be sure both the ceiling cover and
the coupler cover are oriented correctly (Figure 3).
5.
Route the motor leads through the hanger ball.
Reinstall the hanger ball (Figure 4) on the
downrod. Reinstall the pin through the two holes in
the downrod. Slide the ball upwards and align the
ball so the pin is captured in the groove in the top
of the hanger ball. Pull the hanger ball up tight
against the pin and securely tighten the setscrew in
the hanger ball. A loose setscrew could create fan
wobble.
Reinstall the hanger ball (Figure 4) on the
downrod. Reinstall the pin through the two holes in
the downrod. Slide the ball upwards and align the
ball so the pin is captured in the groove in the top
of the hanger ball. Pull the hanger ball up tight
against the pin and securely tighten the setscrew in
the hanger ball. A loose setscrew could create fan
wobble.
6.
The fan comes with black and white leads that are
80” long. Before installing fan, measure up
approximately 6 to 9-inches above top of hanger
ball/downrod assembly. Cut off excess leads and
strip back insulation 1/2-inch from end of leads.
80” long. Before installing fan, measure up
approximately 6 to 9-inches above top of hanger
ball/downrod assembly. Cut off excess leads and
strip back insulation 1/2-inch from end of leads.
7.
Position one fan blade on the flange assembly of
the motor assembly and secure by installing four
#10-24 x .375” flat head screws and four #10 x .50”
flat washers (supplied) (Figure 5).
the motor assembly and secure by installing four
#10-24 x .375” flat head screws and four #10 x .50”
flat washers (supplied) (Figure 5).
8.
Install the remaining four fan blades using the
same procedure.
same procedure.
NOTE: Take care not to scratch fan housing when
installing blades.
installing blades.
9.
You have now completed the initial assembly of your
new ceiling fan. You can now proceed with hanging
and wiring your fan.
new ceiling fan. You can now proceed with hanging
and wiring your fan.
ETL Model No.: CF550
#10-24 x .375" FLAT HEAD
SCREWS (4 per blade)
SCREWS (4 per blade)
#10 x .50" FLAT
WASHERS
(4 per blade)
WASHERS
(4 per blade)
BLADE FLANGE
FAN BLADE
Figure 5
To reduce the risk of personal injury, do not bend the
blade flange when installing the blade flanges,
balancing the blades or cleaning the fan. Do not
insert foreign objects in between rotating fan blades.
blade flange when installing the blade flanges,
balancing the blades or cleaning the fan. Do not
insert foreign objects in between rotating fan blades.
WARNING
!
It is critical that the pin in the hanger ball is properly
installed and the setscrew securely tightened.
Failure to verify that the pin and setscrew are
properly installed could result in the fan falling.
installed and the setscrew securely tightened.
Failure to verify that the pin and setscrew are
properly installed could result in the fan falling.
WARNING
!
CEILING
COVER
COVER
DOWNROD
HANGER BALL
PIN
SETSCREW
Figure 4