Emerson CF742PFOB Manuel D’Utilisation
THIS FAN IS SUITABLE FOR DAMP LOCATIONS SUCH AS
COVERED PORCHES, COVERED PATIOS, AND COVERED DECKS.
ANYWHERE THERE IS A ROOF OVERHEAD.
This Manual is Designed to Make it as Easy as
Possible for You to Assemble, Install,
Operate and Maintain Your Ceiling Fan
1. Pass the 80" motor leads through the opening in the
ceiling cover. Be sure the cover is oriented
correctly.
correctly.
2. Separate, untwist and unkink the three motor leads.
Route the motor leads through the hanger
ball/downrod assembly.
ball/downrod assembly.
3. Remove the two setscrews from the motor coupling.
Align the clevis pin holes in the downrod with the
holes in the motor coupling. Install the clevis pin
and secure with the hairpin clip (Figure 1). The
clevis pin must go through the holes in the motor
coupling and the holes in the downrod. Be sure to
holes in the motor coupling. Install the clevis pin
and secure with the hairpin clip (Figure 1). The
clevis pin must go through the holes in the motor
coupling and the holes in the downrod. Be sure to
push the straight leg of the hairpin clip through the
hole near the end of the clevis pin until the curved
portion of the clip snaps around the clevis pin. Pull
on the hanger ball to make sure the clevis pin is
properly installed.
hole near the end of the clevis pin until the curved
portion of the clip snaps around the clevis pin. Pull
on the hanger ball to make sure the clevis pin is
properly installed.
3
Tools Needed for Assembly
One Phillips head screwdriver
One stepladder
One wire stripper
Three wire connectors (supplied).
One stepladder
One wire stripper
Three wire connectors (supplied).
MATERIALS
Wiring, electrical box and box connectors must be of
type required by the local code. The minimum wiring
would be a 3-conductor (2-wire with ground) of
following sizes:
type required by the local code. The minimum wiring
would be a 3-conductor (2-wire with ground) of
following sizes:
Installed Wire Length
Wire Size A.W.G.
Up to 50 ft.
14
50 - 100 ft.
12
Check to see that you have received the following
parts:
a. Fan motor assembly
b. Five fan blades
c. One ceiling cover
d. Five blade flanges
e. One hanger ball/downrod assembly
f. One hanger bracket.
g. One loose parts bag containing:
parts:
a. Fan motor assembly
b. Five fan blades
c. One ceiling cover
d. Five blade flanges
e. One hanger ball/downrod assembly
f. One hanger bracket.
g. One loose parts bag containing:
1. Sixteen 3/16-24 x 1/2" screws
2. Eleven 1/4-20 x 7/16" blade flange screws
3. One pull chain pendant
4. One pull chain coupling
5. Three wire connectors
6. One clevis pin
7. One hairpin clip
8. Two threaded studs
9. Two lockwashers
2. Eleven 1/4-20 x 7/16" blade flange screws
3. One pull chain pendant
4. One pull chain coupling
5. Three wire connectors
6. One clevis pin
7. One hairpin clip
8. Two threaded studs
9. Two lockwashers
10. Two knurled knobs
NOTE: Place the parts from the loose parts bag in
a small container to keep them from being lost.
a small container to keep them from being lost.
Unpacking Instructions
For your convenience, check-off boxes are provided next to each assembly step. As each step is
completed, place a check mark in the box. This will insure that all steps have been completed and will be
helpful in finding your place should you be interrupted.
completed, place a check mark in the box. This will insure that all steps have been completed and will be
helpful in finding your place should you be interrupted.
How to Put Your Ceiling Fan Together
Before assembly your ceiling fan, refer to section on
proper method of wiring your fan (page 5). If you feel
you do not have enough wiring knowledge or
experience, have your fan installed by a licensed
electrician.
proper method of wiring your fan (page 5). If you feel
you do not have enough wiring knowledge or
experience, have your fan installed by a licensed
electrician.
WARNING
!
Do not install or use fan if any part is damaged or
missing. Call Toll-Free:
missing. Call Toll-Free:
1-800-654-3545
This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use with this product by
Emerson Company. Substitution of parts or
accessories not designated for use with this product
by Emerson Company could result in personal injury
or property damage.
supplied with this product and/or any accessories
designated specifically for use with this product by
Emerson Company. Substitution of parts or
accessories not designated for use with this product
by Emerson Company could result in personal injury
or property damage.
WARNING
!
WARNING
!
It is critical that the clevis pin in the motor coupling
is properly installed and the setscrew securely
tightened. Failure to verify that the pin and setscrew
are properly installed could result in the fan falling.
is properly installed and the setscrew securely
tightened. Failure to verify that the pin and setscrew
are properly installed could result in the fan falling.
WARNING
!