Emerson CF830GES00 Manuel D’Utilisation
1.
Position the flange medallion upside down on a
soft, clean surface. Place the blade with the
decorative side facing down onto the flange
medallion. Attach the flange assembly to the blade
and flange medallion using the four #10-32 x
22mm oval head screws as shown in Figure 2.
Repeat for the four remaining blades.
soft, clean surface. Place the blade with the
decorative side facing down onto the flange
medallion. Attach the flange assembly to the blade
and flange medallion using the four #10-32 x
22mm oval head screws as shown in Figure 2.
Repeat for the four remaining blades.
NOTE: Take care not to scratch fan housing when
installing blades.
installing blades.
2.
The flange assemblies have interlocking tabs, be
sure that the flanges are installed in a clockwise
manner to engage the interlocking feature. Be sure
all the flanges are properly engaged and then
tighten the flange screws. If one of the flanges do
not seat properly on the motor hub, loosen the
adjacent flange screws, re-engage and reseat the
flanges, then tighten the screws again.
sure that the flanges are installed in a clockwise
manner to engage the interlocking feature. Be sure
all the flanges are properly engaged and then
tighten the flange screws. If one of the flanges do
not seat properly on the motor hub, loosen the
adjacent flange screws, re-engage and reseat the
flanges, then tighten the screws again.
3.
Attach the blade/flange assembly using two
1/4-20 x 12mm oval head screws (Figure 3). Install
the remaining four fan blades assemblies using the
same procedure.
1/4-20 x 12mm oval head screws (Figure 3). Install
the remaining four fan blades assemblies using the
same procedure.
4.
Gently snug all flange screws to the motor
housing, working around the housing in a
clockwise sequence. Failure to follow this
procedure could result in fan wobble. This
completes the blade installation.
housing, working around the housing in a
clockwise sequence. Failure to follow this
procedure could result in fan wobble. This
completes the blade installation.
SHIPPING
RETAINERS (5)
RETAINERS (5)
FAN BLADE
#10-32 x 22mm OVAL
HEAD BLADE SCREW
(4 per blade/flange)
HEAD BLADE SCREW
(4 per blade/flange)
FLANGE MEDALLION
ASSEMBLY
ASSEMBLY
FAN FLANGE
Figure 2
If your fan is to replace an existing ceiling light fixture,
turn electricity off at the main fuse box at this time
and remove the existing light fixture.
turn electricity off at the main fuse box at this time
and remove the existing light fixture.
Turning off wall switch is not sufficient. To avoid
possible electrical shock, be sure electricity is turned
off at the main fuse box before wiring. All wiring must
be in accordance with national and local codes and
the ceiling fan must be properly grounded as a
precaution against possible electrical shock.
possible electrical shock, be sure electricity is turned
off at the main fuse box before wiring. All wiring must
be in accordance with national and local codes and
the ceiling fan must be properly grounded as a
precaution against possible electrical shock.
WARNING
!
Your new ceiling fan will require a grounded electrical
supply line of 120 volts AC, 60 Hz, 15 amp circuit.
supply line of 120 volts AC, 60 Hz, 15 amp circuit.
The outlet box must be securely anchored and
capable of withstanding a load of at least 50 pounds.
capable of withstanding a load of at least 50 pounds.
To reduce the risk of fire, electric shock, or personal
injury, mount fan to outlet box marked “Acceptable
for Fan Support of 50 lbs. or Less”, and use screws
supplied with outlet box. Most outlet boxes
commonly used for support of light fixtures are not
acceptable for fan support and may need to be
replaced. Consult a qualified electrician if in doubt.
injury, mount fan to outlet box marked “Acceptable
for Fan Support of 50 lbs. or Less”, and use screws
supplied with outlet box. Most outlet boxes
commonly used for support of light fixtures are not
acceptable for fan support and may need to be
replaced. Consult a qualified electrician if in doubt.
WARNING
!
Electrical Requirements
Ceiling Fan Assembly
Procedures
To avoid possible fire or shock, follow all wiring
instructions carefully. Any electrical work not
described in these instructions should be done or
approved by a licensed electrician.
instructions carefully. Any electrical work not
described in these instructions should be done or
approved by a licensed electrician.
WARNING
!
4
IMPORTANT: Your ceiling fan is supplied with an
Fan/Light Dual Slide Wall Control (transmitter).
This allows you to regulate your ceiling fan speed,
airflow direction, and light intensity. Optional
Emerson Electric Remote and Wall Control may
also be used, see store or catalog.
Fan/Light Dual Slide Wall Control (transmitter).
This allows you to regulate your ceiling fan speed,
airflow direction, and light intensity. Optional
Emerson Electric Remote and Wall Control may
also be used, see store or catalog.
IMPORTANT: Your ceiling fan will not function
properly and may be damaged, if used with any
wall dimmer switch or control other than the
Emerson controls listed above.
properly and may be damaged, if used with any
wall dimmer switch or control other than the
Emerson controls listed above.
IMPORTANT: Remove the five motor retainers
from the motor hub and discard the retainers and
retainer screws before installation of flange/blade
assembly (Figure 1).
from the motor hub and discard the retainers and
retainer screws before installation of flange/blade
assembly (Figure 1).
U.L. Model No.: CF830
Figure 1