Johnson Controls 340968-XIM-A-0108 Manuel D’Utilisation
340968-XIM-A-0108
Johnson Controls Unitary Products
3
GENERAL
YORK Model DNA units are cooling/heating air conditioners
designed for outdoor installation. Only gas piping, electric
power and duct connections are required at the point of
installation.
designed for outdoor installation. Only gas piping, electric
power and duct connections are required at the point of
installation.
The gas-fired heaters have spark to pilot ignition. The tubular
heat exchangers are aluminized steel.
heat exchangers are aluminized steel.
This appliance is not to be used for temporary heating of
buildings or structures under construction.
buildings or structures under construction.
Installer should pay particular attention to the words; NOTE,
CAUTION, and WARNING. NOTES are intended to clarify or
make the installation easier. CAUTIONS are given to prevent
equipment damage. WARNINGS are given to alert the
installer that personal injury and/or equipment damage may
result if installation procedure is not handled properly.
CAUTION, and WARNING. NOTES are intended to clarify or
make the installation easier. CAUTIONS are given to prevent
equipment damage. WARNINGS are given to alert the
installer that personal injury and/or equipment damage may
result if installation procedure is not handled properly.
INSPECTION
As soon as a unit is received, it should be inspected for possi-
ble damage during transit. If damage is evident, the extent of
the damage should be noted on the carrier's freight bill. A
separate request for inspection by the carrier's agent should
be made in writing.
ble damage during transit. If damage is evident, the extent of
the damage should be noted on the carrier's freight bill. A
separate request for inspection by the carrier's agent should
be made in writing.
RENEWAL PARTS
Contact your local York® parts distribution center for autho-
rized replacement parts.
rized replacement parts.
APPROVALS
Design certified by CGA and AGA listed as follows:
1.
For use as a forced air furnace with cooling unit.
2.
For outdoor installation only.
3.
For installation directly on combustible flooring or, in
U.S., on wood flooring or Class A; B; C roof covering
material.
U.S., on wood flooring or Class A; B; C roof covering
material.
4.
For installation on combustible material.
5.
For use with natural gas and/or propane (LP) gas. Not
suitable for use with conventional venting systems.
suitable for use with conventional venting systems.
This product must be installed in strict compliance
with the enclosed installation instructions and any
applicable local, state, and national codes includ-
ing, but not limited to, building, electrical and
mechanical codes.
with the enclosed installation instructions and any
applicable local, state, and national codes includ-
ing, but not limited to, building, electrical and
mechanical codes.
Improper installation may create a condition where
the operation of the product could cause personal
injury or property damage.
the operation of the product could cause personal
injury or property damage.
FIGURE 1 - PRODUCT NOMENCLATURE
D
2
N A
N
PRODUCT CATEGORY
3
0
6
0
6
3
0
6
VOL TAGE CODE
06 = 208/230-1-60
D = Single Package Air Conditioner
PRODUCT IDENTIFIER
NA = 10 SEER Gas Heat/Electric
NOMINAL COOLING
CAPACITY (MBH)
N = Natural Gas Heat Installed
FACTORY
INSTALLED GAS HEAT
036 = 36,000 BTUH
056 = 56,000 BTUH
065 = 65,000 BTUH
072 = 72,000 BTUH
090 = 90,000 BTUH
110 = 110,000 BTUH
056 = 56,000 BTUH
065 = 65,000 BTUH
072 = 72,000 BTUH
090 = 90,000 BTUH
110 = 110,000 BTUH
NOMINAL GAS HEATING
OUTPUT CAPACITY
PRODUCT GENERATION
2 = 2nd Generation
3 = 3rd Generation
3 = 3rd Generation
018 = 18,000 BTUH
024 = 24,000 BTUH
030 = 30,000 BTUH
036 = 36,000 BTUH
042 = 42,000 BTUH
060 = 60,000 BUTH
024 = 24,000 BTUH
030 = 30,000 BTUH
036 = 36,000 BTUH
042 = 42,000 BTUH
060 = 60,000 BUTH